background image

© Danfoss | 2022.11| 21

LGB53080

Termix VX-IV - 3 Series DS Fully insulated

Grundfos UPM3 AUTO instructions

Control mode

Each push on the button switches to the next program setting.

The choice of operation mode depends on the type of heating 

system and the pressure loss in the system.

Remark: 

The circulator pump should run for 10 minutes during the first installation.

Function

 

/ PP

Green

 

/ CP

Green

Yellow

Yellow

Yellow

Proportional pressure Auto adapt

Constant pressure auto adapt

Proportional pressure 1

Proportional pressure 2 (factory setting)

Proportional pressure 3 - Max

Constant pressure 1

Constant pressure 2

Constant pressure 3 

Constant curve 1

Constant curve 2

Constant curve 3 - Max

Function

 

/ PP

Red

 

/ CP

Green             

Yellow

Yellow

Yellow

Power supply failure

Blocked

Supply voltage low

Electrical error

Alarm status

Settings

Recommended Circulator Pump Settings

The circulator pump (10) setting will be individual to each installation, dependent on the pressure drop across the secondary circuit and the space 

heating design flow rate. 

The below recommendations are intended as a guide.

PP 1 

PP 2

PP 3

CP 1

CP 2

CP 3

CC 1

CC 2

CC 3

Traditional TRVs

Pressure Independent TRVs (PITRVs)

Traditional UFH

UFH with pressure Independent inserts

Summary of Contents for 3 Series





























Reviews: