background image

1.4.6.1 No Options

1.

Position the 3 AC input busbars in the drive.

2.

Fasten 1 nut (13 mm) in the center of the middle
busbar.

3.

Secure 6 nuts (13 mm) at the bottom of the AC input
busbars, 1 per phase.

4.

Fasten 3 nuts (13 mm) at the top of the AC input
busbars, 1 per phase.

5.

Position the air baffle in the drive, and fasten with 4
screws (T25).

1.4.6.2 Mains Fuses Only

1.

Position the AC input busbars in the drive.

2.

Fasten 3 nuts (13 mm) at the top of the AC input
busbars, 1 per phase.

3.

Position the 3 mains fuses in the drive.

4.

Fasten 6 nuts (13 mm), 1 at each end of the 3 fuses.

5.

Position the air baffle in the drive, and fasten with 4
screws (T25).

1.4.6.3 RFI Filter Only

1.

Connect the RFI cable to MK100 on the RFI filter card.

2.

Position the RFI filter in the drive.

3.

Fasten 4 thread-cutting screws (T20), connecting the
RFI filter to the side channels of the drive.

4.

Secure 6 nuts (13 mm) at the bottom of the RFI filter,
2 per phase.

5.

Secure 3 nuts (13 mm) at the top of the RFI filter, 1
per phase.

6.

Position the air baffle in the drive, and fasten with 4
screws (T25).

1.4.6.4 Mains Fuses and RFI Filter

1.

Connect the RFI cable to MK100 on the RFI card.

2.

Position the RFI filter in the drive.

3.

Fasten 4 thread-cutting screws (T20), connecting the
RFI filter to the side channels of the drive.

4.

Secure 3 nuts (13 mm) at the top of the RFI filter, 1
per phase.

5.

Secure the 3 mains fuses by fastening 6 nuts (13
mm), 1 at each end of the fuses.

6.

Position the air baffle in the drive, and fasten with 4
screws (T25).

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on
order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss
and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.

Danfoss A/S
Ulsnaes 1
DK-6300 Graasten
vlt-drives.danfoss.com

 

*MI70Y202*

MI70Y202

130R0721

07/2018

Summary of Contents for 176F6516











Reviews: