background image

1.5.6 Installing Gaskets to the Back of a

D7h/D8h Enclosures

NOTICE

APPLYING GASKETS

This kit contains gaskets to ensure a proper seal between
metal parts. Before adhering a gasket to a part, check that
the part matches the gasket and that no holes are covered.
Remove paper backing and place the sticky side on the part.

1.

Install 1 of the vent gaskets (2) around the exhaust
vent opening on the back of the enclosure.

2.

On top of the gasket, install the exhaust spacer (1) to
the back of the enclosure panel using 8 M5x18
screws. Torque to 5.1 Nm (45 in-lb).

3.

Install 1 of the vent gaskets (2) to the exhaust spacer.

4.

Apply the 2 labels (3) over the back-channel form
holes.

5.

Install 1 of the vent gaskets (5) around the intake
vent opening on the back of the enclosure.

6.

On top of the gasket, install the intake spacer (4) to
the back of the enclosure panel using 8 M5x18
screws. Torque to 5.1 Nm (45 in-lb).

7.

Install 1 of the vent gaskets (5) to the intake spacer.

8.

Install the slot gasket (6) to cover the mounting holes
used to secure the enclosure to the base plate.

1

Exhaust spacer

2

Exhaust  vent  gaskets

3

Slot  gasket

4

Intake  spacer

5

Intake  vent  gaskets

6

Slot  gasket

Illustration 1.13 Installing Sealing Gaskets to Back Panel for the

D7h/D8h Frequency Converters

Installation Instructions

In-back/Out-back Cooling Kit for D5h/D6h and D7h/D8h Enclosures VLT® Series FC 102, FC 202,
and FC 302

8

Danfoss A/S © 10/2016 All rights reserved.

MI70F102

Summary of Contents for 176F3530











Reviews: