manualshive.com logo in svg

Danfoss 176F3530, Installation Instructions Manual, Page: 7 / 10

Share
Download
Danfoss 176F3530 Installation Instructions Manual Download Page 7

1.5.5 Installing Gaskets to the Back of a

D5h/D6h Enclosure

NOTICE

APPLYING GASKETS

This kit contains gaskets to ensure a proper seal between
metal parts. Before adhering a gasket to a part, check that
the part matches the gasket and that no holes are covered.
Remove paper backing and place the sticky side on the part.

For the following steps, refer to 

Illustration 1.12

.

D5h/D6h enclosures with a pedestal

1.

Install the mounting gasket (1) to the top of the
enclosure.

2.

Install 1 of the vent gaskets (5) around the exhaust
vent opening on the back of the enclosure.

3.

On top of the gasket, install the exhaust spacer (2) to
the back of the enclosure panel using 6 M5x18
screws. Torque to 5.1 Nm (45 in-lb).

4.

Install 1 of the vent gaskets (5) to the exhaust spacer.

5.

Apply the 2 labels (6) over the back-channel form
holes.

6.

Install 1 of the vent gaskets (7) around the intake
vent opening on the back of the enclosure.

7.

On top of the gasket, install the intake spacer (3) to
the back of the enclosure panel using 6 M5x18
screws. Torque to 5.1 Nm (45 in-lb).

8.

Install 1 of the vent gaskets (7) to the intake spacer.

9.

Install the slot gasket (4) to cover the mounting holes
used to secure the enclosure to the base plate.

D5h/D6h enclosures without a pedestal

1.

Install 1 of the vent gaskets (5) around the exhaust
vent opening on the back of the enclosure.

2.

Apply the 2 labels (6) over the back-channel form
holes.

3.

Install 1 of the vent gaskets (7) around the intake
vent opening on the back of the enclosure.

4.

Install the slot gasket (4) to cover the mounting holes
used to secure the enclosure to the base plate.

1

Mounting  gasket

2

Exhaust spacer (Used on pedestal units only)

3

Intake spacer (Used on pedestal units only)

4

Slot  gasket

5

Exhaust vent gaskets

6

Label

7

Intake vent gaskets

1) Gasket between vent spacer and mounting backplate/wall is used

only on pedestal-mounted units.

Illustration 1.12 Installing Sealing Gaskets to Back Panel for the

D5h/D6h Frequency Converters

Installation Instructions

In-back/Out-back Cooling Kit for D5h/D6h and D7h/D8h Enclosures VLT® Series FC 102, FC 202,
and FC 302

MI70F102

Danfoss A/S © 10/2016 All rights reserved.

7

Summary of Contents for 176F3530











Reviews:

No comments