D&H DH05A/B Manual Download Page 14 | Manualshive

Page: 14 / 36

D&H DH05A/B Manual Download Page 14

14

7.3

Operation

Put  the  locomotive on  the  programming  track  and  read out  the  programming  parameters  of the decoder.
The  default  value  should  be  01-542.  Program  the  desired  locomotive  address  and  start  running  the
locomotive  keeping  the  other  parameter  values.  After  the  first  check  you  can  vary  the  parameters  of  the
engine freely according to your requirements.

In case your programming device indicates "error", please check again the correct wiring of the locomotive
and  pay  attention  to  the  wiring  instructions  of  the  programming  track.  Never  put  such  a  locomotive  into
operation!

7.4

Explication of the signal-stopping section

One-part signal-stopping section:

In front of the signal one track section is controlled by a diode. The decoder must be programmed on
one-part stopping section (-). The locomotive will be braked to a halt.

Two-part signal-stopping section:

In front of the signal there are two track sections. The first one is controlled by a diode and the
locomotive will be braked down to internal speed step 3 in this section. The second one is without
supply and the locomotive will stop just in front of the signal. The decoder must be programmed on
two-part stopping section (=).

«
...
12
13
14
15
16
...
»

Summary of Contents for DH05A/B





































Reviews:

No comments