background image

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

ELECTRICAL REQUIREMENTS

All wiring must comply with local and national 

codes and must be installed by a qualifi ed 

electrician. Check the available power supply and 

resolve any wiring problems before installing and 

operating this appliance.

This 115 V appliance may be used in any properly 

wired, general purpose household receptacle. 

The rating plate located on the right side of the 

appliance just above the power cord contains 

electrical and other technical data.

SAFETY INSTRUCTIONS

This appliance is not intended for use by persons, 

including children, with reduced physical, sensory 

or mental capabilities or lack of experience and 

knowledge, unless they have been given supervision 

or instruction concerning use of the appliance by a 

person responsible for their safety.

Children should be supervised to ensure that they 

do not play with the appliance.

Do not install the appliance where leakage of 

combustible gas is suspected.

POWER CORD INSTRUCTIONS

The power supply cord contains a current device 

that senses damage to the power cord. To test the 

power supply cord:

1.  Plug in the appliance.

2.  Press the TEST button on the power supply cord. 

The RESET button will click and pop out.

3.  Press the RESET button until it clicks into place.

4.  The power supply cord is now supplying 

electricity to the appliance.

Do not use this device to turn the appliance on or 

off. Ensure that the RESET button is pushed in for 

correct operation. The power supply cord must be 

replaced if it fails to reset when the TEST button is 

pushed.

2

GROUNDING INSTRUCTIONS

This appliance must be grounded. Grounding 

reduces the risk of electrical shock by providing an 

escape wire for the electrical current. 

This appliance has a cord that has a grounding 

wire with a 3-prong plug. The power cord must be 

plugged into an outlet that is properly grounded. 

If the outlet is a 2-prong wall outlet, it must be 

replaced with a properly grounded 3-prong wall 

outlet.

WARNING - 

Improper use of the grounding 

plug can result in a risk of electric shock. 

Consult a qualifi ed electrician or service agent 

if the grounding instructions are not completely 

understood, or if doubt exists as to whether the 

appliance is properly grounded.

Do not connect your appliance to extension 

cords or together with another appliance in the 

same wall outlet.

 Do not splice the power cord. 

Do not under any circumstances cut or remove the 

third ground prong from the power cord. Do not 

use extension cords or ungrounded (two prongs) 

adapters.

If the power supply cord is damaged, it must be 

replaced by the manufacturer, its service agent or 

similar qualifi ed person in order to avoid hazard.

Summary of Contents for DTAC080BAUWDB












Reviews: