danalock V3-BTZB Technical Manual Download Page 9

 
V3-BTZB 

 

 

 

Danalock V3-BTZB, Technical Manual v.1.5, May 2017 

  Page 9 

The V3-BTZB unit cannot be turned off after installation, so any doors installed with the 
V3-BTZB etc. must not operate near health care facilities when any regulations posted in 
these areas prohibit the use of wireless phones or two-way radios. Hospitals and health 
care facilities may be using equipment that could be sensitive to external RF energy. 
 
 

Potentially Explosive Atmospheres 

The V3-BTZB unit cannot be turned off after installation, so any building installed with V3-
BTZB etc. must not be located in an area with a potentially explosive atmosphere and 
obey all signs and instructions not to use V3-BTZB in such areas. Sparks in such areas 
could cause an explosion or fire resulting in bodily injury or even death. 
 
Areas with a potentially explosive atmosphere are often, but not always marked clearly. 
Potential areas may include: fueling areas (such as gasoline stations); below deck on 
boats; fuel or chemical transfer or storage facilities; areas using liquefied petroleum gas 
(such as propane or butane); areas where the air contains chemicals or particles (such as 
grain, dust, or metal powders); and any other area where it would normally be advisable 

not to

 install the V3-BTZB. 

 
 

Specific Human Absorption Rates (SAR) 

THE V3-BTZB UNIT IS NOT DESIGNED TO BE WORN ON A PERSON’S BODY. AS 
SUCH, BODY WORN TEST POSITIONS FOR THE V3-BTZB UNIT  
ARE NOT REQUIRED BY EITHER THE IEC 62311 FOR BLUETOOTH LE OR 
FCC/IEEE/ICNIRP REQUIREMENTS FOR BLUETOOTH LE. 
 
The V3-BTZB unit is not intended for handheld use or to be worn on the body. A minimum 
separation of eight (8”) inches (20 cm) is to be maintained between the V3-BTZB and any 
persons’ body. Additional information on Specific Absorption Rates (SAR)

 

Battery Safety Information 

Adhere to the following guidelines to avoid the risk of fire or explosion: 
 
1.  Dispose of the used battery according to the instructions provided with the battery. 
2.  Do not drop, puncture, disassemble, mutilate, or incinerate the battery. 
3.  Touching both terminals of a battery with a metal object will short circuit the battery. Do 

not carry batteries loosely if the contacts may touch coins, keys, and other metal 
objects (such as in pockets or bags). 

4.  Do not stack batteries taken out of the carry case. 
5.  Do not heat the batteries to try to rejuvenate their charge. 
6.  Do not exceed the temperature ranges or other environmental conditions specified by 

the battery manufacturer. 

7.  Never use the V3-BTZB without the battery cover installed. 
 
 
 

 

Summary of Contents for V3-BTZB





















Reviews: