background image

DVE-4 / DVE-8 / DVE-16

www.dallmeier.com

5

2  Safety Instructions

Only use the device if it is technically in proper working condition and for the intended pur-

pose while keeping safety and potential dangers in mind.

Qualified Personnel

The installation, mounting, connection, commissioning and configuration of the device may 

only be carried out by qualified personnel.

This also applies to the maintenance, testing and repair, whereat the regulations of the DIN 

VDE 0701 series of standards (repair, modification and inspection of electrical appliances) 

must be followed.

Regulations

The use of video and audio surveillance systems is, in general, strictly regulated. Inform 

yourself about the currently valid laws and regulations regarding data, worker and environ-

mental protection before using the device and ensure compliance with them.

System Components

Only use internal components that have been tested and approved by Dallmeier. Inap-

propriate internal components may cause malfunctions, damages and data loss and may 

result in the loss of warranty.

Modifications

Do not make any modifications to the hardware or software that have not been tested and 

approved by Dallmeier.

Inappropriate  modifications  may  cause  malfunctions,  damages  and  data  loss  and  may 

result in the loss of warranty.

Documentation

Read the documents included in the delivery carefully and thoroughly. Always observe the 

contained instructions, notes and warnings.
The product documentation contains several documents which are included in the delivery 

in printed form and/or on a digital medium.
Store all documents in legible condition in a suitable location in order to provide for later 

consultation.

Condensation Water

If the device is brought from a cold to a warm environment, resulting condensation water 

may cause malfunctions and damages.

In this case, wait (up to 8 hours) until the device has reached room temperature before 

commissioning.

Earthing & Equipotential Bonding

For  the  safety  of  persons  (protection  against  dangerous  contact  voltages)  and  devices 

(protection  against  over-voltages)  and  the  immunity  of  information  and  communication 

technology  equipment  to  electromagnetic  interferences  (EMI),  all  protective  measures, 

which are specified by the currently valid DIN, VDE and ISO standards and which provide 

for a standard-compliant earthing and a correct equipotential bonding of electrical and elec-

tronic devices, are mandatory and must be fulfilled by all means.

Summary of Contents for DVE-16


































Reviews: