manualshive.com logo in svg

DALBO MAXIROLL 1030, Manual

Share
Download
DALBO MAXIROLL 1030 Manual Download Page 33

 

 

MAXIROLL 

 

 

Page 33 

Mounting 
1

 

Fit new gaskets in upper part and collar shoe. 

2

 

Lubricate thread in upper part (pos. 3) and cylinder tube (pos. 1) with grease 
or oil. 

3

 

Fit upper part (pos. 3) on ram shaft. 

4

 

 Fit collar shoe (pos. 4) and secure ram shaft (pos. 2) with Loctite. Ensure that 
thread  is  absolutely  clean  and  free  of  oil  or  other  impurities  before  applying 
Loctite. Do not fill with oil for 12 hours after use of Loctite. 

5

 

Lubricate outer collar shoe gasket in contact with cylinder tube and inside of 
cylinder tube with oil, push ram into centre position. 

6

 

Fit upper part onto cylinder tube and tighten. 

7

 

For fitting cylinder see ”

Replacing crackerboard depth-adjustment cylinder

”.

 

 

Removal/fitting wheel 

Before removing wheel, fully extend roller with rings resting on ground. Wheels will 
then be raised free of ground.  
Remove wheel nuts. Remove wheel. Replace wheel, hand-tighten wheel nuts. Lower 
wheels to ground. Tighten wheel nuts to 300 Nm. 
 

 

Ensure wheel nuts and wheel surfaces are clean to avoid nuts loosening. 
 

 
Replacing wheel bearings 

 

Fig. 31 

1.

 

Remove hub cap pos. 21. 

2.

 

Remove split pin pos. 20. 

3.

 

Remove castle nut pos. 19. 

4.

 

Hub  housing  can  now  be  removed 
from shaft. 

5.

 

Remove bearings pos. 17+18. 

6.

 

Remove seal ring pos. 19. 

 

 
Mounting  

1.

 

Fit bearing outer rings pos. 17+18 in hub housing pos. 22 

2.

 

Fit seal ring pos. 16. 
 
 
 

3.

 

Fit bearing inner ring pos. 18 on axle pos. 2 and fit axle in hub housing 

4.

 

Fit bearing inner ring pos. 17 on axle pos. 2 

Summary of Contents for MAXIROLL 1030











































Reviews:

No comments

Brands by name

Popular brands

Load more brands