manualshive.com logo in svg

DALBO MAXIDISC 300, Operator'S Manual

Share
Download
DALBO MAXIDISC 300 Operator'S Manual Download Page 21

 

 

MAXIDISC 

 

 

Side 21 

Replacements and Repairs 

 

Safety is important in connection with all repair work on the MAXI-
DISC. The following safety precautions and the precautions listed in 
the beginning of this manual must be observed. 

 

 

Before performing any adjustments, maintenance or repairs on 
the  machinery, always  unfold the  MAXIDISC and  lower  the  im-
plement to the ground or secure in transport position, set the 
tractor brakes, turn off the engine and remove the ignition key 
to avoid unintentional operation. 

 

 

Pay careful attention to safety when performing repair work on 
the hydraulic  system.  Remove  hydraulic  pressure prior  to do-
ing any maintenance.  

 

 

After making repairs to the hydraulic system, always bleed air 
out of the system before operating the MAXIDISC again to avoid 
any possible personal injury or mechanical breakdown or dam-
age. 

 

Hydraulic System 

Replacing angle adjustment cylinder 
Lower the MAXIDISC to the ground and relieve the pressure in the hydraulic system.  
 

 

Fig. 9 

1

 

Disconnect the hoses. 

2

 

Remove the pins. 

3

 

The cylinder is now free. Install 
a  new  cylinder.  Follow  the  in-
structions in reverse order. 

 

 

 

 

After installing the new cylinder, always bleed air out of the system 
and check for leaks. 
 

 

Summary of Contents for MAXIDISC 300




























Reviews:

No comments

Brands by name

Popular brands

Load more brands