background image

Troubleshooting guide. 
 

Problem   Possible 

cause 

  Solution 

 
Gauge will not light up   

Red wire does not have  

Connect to a location that has power. 

     

 

power. 

 

 

 

 

Black wire is not getting  

Connect ground to a different location. 

     

 

good 

ground. 

 

 

 

 

Gauge is damaged. 

 

Return gauge for repair.  (see instructions) 

Gauge lights up, but 

 

Sender is not connected 

 

Connect wires from gauge to sender 

  displays “EE”.   

 

  to gauge. 

 

 

  terminals. 

 

 

 

 

Wire between gauge and 

Test and replace wire. 

     

 

sender 

is 

broken. 

 

 

 

 

Sender is not grounding  

Sender grounds through it’s mounting 

     

 

properly. 

   

 

threads.  Make sure the threads are  

         

 

clean. 

 

Do Not Use Tape or Sealant

 

 

 

 

 

 

 

 

 

  

on Sender Threads. 

 

 

 

 

Gauge is damaged. 

 

Return gauge for repair.  (contact factory) 

 

 

 

 

Sender is damaged. 

 

Return for replacement.  (see instructions) 

Gauge lights up, but  

 

Sender wire is shorted to 

Check wire for damaged insulation, replace 

  displays “--”.   

 

  ground. 

 

 

  if necessary. 

 

 

 

 

Gauge is damaged. 

 

Return gauge for repair.  (contact factory) 

Gauge lights up, but does 

Loose connection on red 

Reconnect red wire. 

  not read correctly. 

 

  power wire. 

 

 

 

 

Poor sender ground. 

 

Make sure sender case is getting a solid ground. 

 

 

 

 

Poor ground connection. 

Move ground to different location 

 

 

 

 

Incorrect sender type.   

Make sure sender has been replaced with 

         

 

the 

correct 

type 

(SEN-03-1). 

Gauge flashes constantly. 

Warning limits are not set 

Reset warning limits. 

     

 

properly. 

 

 

 

 

Vehicle has improper air 

 

Check air level and air pump. 

 

 

 

 

  pressure. 

External warning indicator 

Indicator not connected   

Check indicator wiring connections. 

  does not work.  

 

  properly. 

 

 

 

 

Indicator does not work.  

Repair or replace indicator. 

 

 

 

 

Gauge output has been   

Return gauge for repair.  (see instructions) 

     

 

damaged. 

Gauge will not dim. 

 

Blue wire is not connected 

Check wiring connections. 

 

 

 

 

  correctly. 

 

 

 

 

Gauge is damaged. 

 

Return gauge for repair.  (contact factory) 

Gauge remains dim at all 

Blue wire is getting power 

Connect blue wire to location that only 

  times.   

 

 

  all of the time.   

 

  has power when the headlights are on. 

    Battery 

is 

very 

low. 

 Recharge or replace vehicle battery. 

 

 

 

 

Gauge is damaged. 

 

Return gauge for repair.  (contact factory) 

 
 

Summary of Contents for Odyssey ODY-19-3







Reviews: