7
MAN# 650666:A
SPEED Speed setup menu
•
>> Speed calibration requires holding the function switch, THEN starting the engine. <<
•
When
“>SPEED” is displayed hold until “RELEASE” is displayed, and release the switch.
•
The selectable options are
“ADJUST”, “AUTO”, “UNIT”, “SERVICE RESET”, “PRESET ODO”, or “BACK”.
•
Press and release the switch to change the selection. Press and hold the switch to select it.
ADJUST Selection
•
This requires riding a known speed with a GPS, or following another vehicle at a known speed.
•
When “>ADJUST” is displayed, press and hold the switch until “RELEASE” is displayed - release the switch.
•
The
options will be “FASTER”, and “SLOWER”, to adjust the speed.
•
Press and release the switch to choose “FASTER” to increase speed, or “SLOWER” to decrease speed.
•
Press and hold the switch until “RELEASE” is displayed to begin adjusting.
•
When riding a known speed, the speedometer will display a speed reading.
•
While the display shows “>TAP TO INCREASE (DECREASE)”, tap the switch to adjust speed.
•
When your speed is correct, hold the switch until “RELEASE” is displayed, release the switch.
•
If you go past your target speed, enter “>ADJUST” again and repeat the process until correct.
•
Exit setup.
AUTO Selection
•
This requires riding a one mile (or kilometer) distance, which must be determined before starting.
•
When “>AUTO” is displayed, hold until “RELEASE” is displayed, and release the switch.
•
The display will show “>BEGIN”. You should be at the beginning of your measured distance to ride.
•
When ready, hold the switch until “RELEASE” is displayed, and release the switch.
•
When
you see “PPM”, you may ride the distance at any speed, and may stop and start.
o
The PPM numbers will increase while riding. If they remain at 000000 please check your speed sensor wiring.
•
When you reach the end of the distance, press and release the switch.
•
Exit setup.
UNIT MPH / km/h Selection
•
It is very important to set the speed unit PRIOR to setting the odometer!
•
When “>UNIT” is displayed, press and hold the switch until “RELEASE” is displayed, release the switch.
•
The display will show UNIT and
“>*MPH” for miles and “km/h” for kilometers.
•
MPH is default. Press and release the switch to choose between MPH or km/h.
•
Hold th
e switch until you see “RELEASE” and release the switch.
SERVICE RESET miles or km to next service setup
Service is a countdown odometer. The service odometer display can be disabled or can be set to count down from 500
–
7500 miles, (800 to 12,000 kilometers). If the service odometer is enabled and display reaches 0 miles/km, it will display
“SERVICE DUE” each time the key is turned on.
•
When
“>SERVICE RESET” is displayed, press and hold the switch until “RELEASE” is displayed and release the switch.
•
The current setting will be displayed. The default is
“>*OFF”, but it could be a value in miles or kilometers.
•
The miles begin at 500 and go up to 7,500 miles in 500 mile increments.
•
The kilometers begin at 800 and go up to 12,000 KM in 800km increments.
•
To change the service odometer, press and release the switch until the desired setting is displayed.
•
Hold the switch until you see “RELEASE”, and release the switch.
•
Exit setup.
PRESET ODO Odometer preset
✓
The odometer starts at zero, but can be preset by the customer within the first 100 miles (161 km) of riding.
✓
After riding more than 100 miles (161 km), the menu option will no longer be displayed.
✓
Correctly select the units to be either MPH or km/h
FIRST
, as the odometer will be set in the selected units.
✓
The preset is in full miles or kilometers only,
no
tenths
✓
The odometer preset can be reset multiple times within the first 100 miles (161 km) of riding.
•
When
“>PRESET ODO” is displayed, press and hold the switch until “RELEASE” is displayed and release the switch.
•
The current miles will be displayed with the left most digit flashing.
•
To change the flashing number, press and release the switch to the desired number.
•
Press and hold the switch until “RELEASE” is displayed, then release the switch.
•
Repeat the process of until the right most digit has been set.
•
With the far right number flashing, press and hold the switch and the display will show
“>SAVE ODO? NO”.
•
Verify the small odometer at the bottom is what you want set.
o
If incorrect hold the button until “RELEASE” is displayed, then release the switch.
o
You can now step through the process again and correct your readings.
o
Turning the key off at any time will discard any attempted odometer settings.
•
If the odometer is correct at the “>SAVE ODO? NO” screen, press and release the switch to change the display to “SAVE
ODO? YES”.
•
When
“>SAVE ODO? YES” is displayed, press and hold the switch until “RELEASE” is displayed and release the switch.
•
Exit setup.
