Dakota Digital MCL-3212, Manual

Page: 5 / 6

MAN# 650378
FUE FUE FUE FUEL LL L Low fuel light and distance to empty setup
If the range feature is turned on, the range reading will initially show the word range until a tank of gas has been driven to
allow the gauge to complete its setup based on your driving. Begin with a full tank of gas and do not refill it until it gets below ¼ tank of
gas. This can be done on multiple trips as long as no fuel is added before it gets low enough. After the initial setup the display will
show
r followed by the calculated distance to empty. This will count down, making adjustments as necessary, until the range is 35
miles (56km) or less and then it will show r Lo . The gauge will continue to make adjustments to match your driving habits with each
fill up. After the initial setup you are not required to wait for the fuel to get below ¼ tank before refilling.
•
Press and release the switch until “ FUEL ” is displayed, then press and hold the switch until “ – ” is displayed.
•
The display will show “ OFF ”, “ SPo ”(Sportster), “ CSt ”(custom), or “ HD ” (2012-up Dyna or Softail).
•
If “ CST ” is chosen, then the following menu options are shown “ FULSET 00 ”, “ FULSET 99 ”, or “ DONE ”.
o
To program a custom fuel curve, with an empty tank press and release the switch until “ FULSET 00 ” is shown.
o
Press and hold the switch until “ – “ is displayed to save the setting.
o
Fill the tank and then press and release the switch until “ FULSET 99 ” is shown.
o
Press and hold the switch until “ – “ is displayed to save the setting.
o
Press and hold the switch when “ DONE ” is displayed to finish the custom setup.
•
If “ CST ” or “ HD ” are chosen, then additional setup options are available. “ SET LO ” and “ RANGE ”.
•
“ SET LO ” allows adjustment of the low fuel warning point. Press and hold the switch while “ SET LO ” is displayed.
o
Release the switch. The speed display will initially show the current setting in percent.
The menu options will be “
DONE ”, “ TEST ”, “ RESET ”, and “ ADJUST ”.
o
“ DONE ” will exit the low fuel setup.
o
“
TEST
” will show the currently measured fuel precent.
o
“ RESET ” will store the factory default of 25%.
o
“ ADJUST ” will allow the current fuel level to be stored as the low fuel level.
•
“ RANGE ” allows the miles to empty feature to be setup. Press and hold the switch while “ RANGE ” is displayed.
o
Release the switch. The display will show whether the range feature is currently “ ON ” or “ OFF ”. Press and
release the switch to change this. Press and hold the switch to save it and continue.
o
If “ ON ” is selected, the next setup options are “ done ” or “ RESET ”.
o
“ DONE ” will exit the range setup.
o
“
RESET
” will reset the gauge to the beginning of the initial range learning.
odoMK odoMK odoMK odoMK Odometer preset
The odometer can be preset by the customer within the first 100 miles. Once the odometer has more than 100 miles, the menu
option will no longer be displayed. Make sure you have correctly selected the units to be either MPH or km/h first. The odometer will
be set in the selected units. Once you have preset the miles you cannot change it again.
WARNING!!: This only allows setting odometer to the nearest mile. Do not use tenths! For example a mileage of 65432.1
should be set to “
065432 ” using this method. If the tenths digit is used, the odometer will read 10 times too high.
•
Press and release the switch until “ -odoMK ” is displayed, then press and hold the switch until “ - ” is displayed.
•
The current ECM odometer reading will be displayed with the left most digit flashing.
•
Press and release the switch to increment the digit. Press and hold the switch to move to the next digit to the right.
•
Continue until the right most digit has been set. Press and hold the switch and the speed display will show “ No ”.
•
Press and hold the switch while “ no ” is displayed to go back and continue changing the odometer display. Turn the key off to
cancel any changes.
•
Press and release the switch to change to speed display to “ yes ”. Press and hold the switch while “ yes ” is displayed to save the
current odometer reading.