Daking Audio Mic Pre 4T Manual Download Page 3

Page: 3 / 14

Contents

Daking Audio Mic Pre 4T

1.1 About Daking Audio

1.2 Quick Start Guide

1.2.1 Don’t read the manual!

1.2.2 Basic Set Up

1.3 The Power Supply

1.4 Back Panel

1.4.1 In General: XLR Connectors and

” TRS Connectors

1.4.2 Microphone Input (XLR)

1.4.3 Line Output (XLR or

” TRS)

1.4.4 Power supply Connection

1.5 Front Panel

1.5.1 LED VU and Peak Meter

1.5.2 Gain Knob

1.5.3

HPF (High-Pass Filter) Knob………………………………...9

1.5.4

” Instrument Input Jack

1.5.5

” Button

1.5.6 Pad Button

1.5.7 +48 Button

1.5.8 Ø Button

1.6 Signal Flow: Patching Into and Out of Your Mic Pre 4T

1.6.1 Microphone to Mic Pre 4T to Audio Interface or Mixer

1.6.2 Via a Patch Bay

1.7 Specifications

..............................................................

.................................................................

....................................................................

......................................................

......................................................................

...................................................................

..............................................................................

......

....................................................

............................................

..................................................

..............................................................................

...................................................

..........................................................................

.................................................

.........................................................................

.......................................................................
.......................................................................

...........................................................................

........

.....

...............................................................

........................................................................

Summary of Contents for Mic Pre 4T















Search results

Summary of Contents for Mic Pre 4T

Reviews:

Related manuals for Mic Pre 4T

Brands by name

Popular brands

Daking Audio Mic Pre 4T, Manual

Search results

Summary of Contents for Mic Pre 4T

Reviews:

Related manuals for Mic Pre 4T

Brands by name

Popular brands