background image

PAGE 8 –  DAKEN Users Manual

INSTRUCTIONS FOR INSTALLATION AND CONNECTION OF 

ELECTRIC FENCES IN AUSTRALIA AS REQUIRED UNDER 

AS3350.2.76

DEFINITIONS

Connecting Lead:

an electric conductor, used to connect the 

energiser

 to the 

electric fence

 or the 

earth electrode.

Electric animal fence:

an 

electric fence

 used to contain animals within or exclude animals from a particular area.

Electric fence:

a barrier which includes one or more electric conductors, insulated from earth, to which electric pulses are 
applied by an 

energiser.

Electric security fence: 

a fence used for security purposes which comprises an 

electric fence

 and a physical barrier electrically 

isolated from the 

electric fence.

GENERAL REQUIREMENTS FOR ELECTRIC FENCES

1.   

Electric fences

 shall be installed and operated so that they cause no electrical hazard to persons, animals 

or their surroundings. 

2.   

Electric fence

 constructions which are likely to lead to the entanglement of animals or persons shall 

be avoided.

3.   An 

electric  fence

  shall  not  be  supplied  from  two  different 

energisers

  or  from  independent  fence 

circuits of the same 

energiser.

 For any two different 

electric fences,

 each supplied from a different 

energiser

 independently timed, the distance between the wires of the two 

electric fences

 shall be at 

least 2.5m. If this gap is to be closed, this shall be effected by means of electrically non-conductive material 

or an isolated metal barrier.

4.   Barbed wire or razor wire shall not be electrified by an 

energiser.

5.   Any part of an 

electric fence

 which is installed along a public road or pathway shall be identified at 

frequent intervals by warning plates securely fastened to the fence posts or firmly clamped to the fence 

wires.

a.   The size of the warning plates shall be at least 100 mm x 200 mm.
b.   The background colour of both sides of the warning plate shall be yellow. The colour on the plate shall 

be black and shall be either:

 i.   The symbol of Figure 4, or
ii.   The substance of TAKE CARE - ELECTRIC FENCE.

c.   The inscription shall be indelible, inscribed on both sides of the warning plate and have a height of at 

least 25 mm.

Summary of Contents for Techfence BT12













Reviews: