background image

 

This information is important in the proper use of your machine. Failure to follow this instruction could result in 

damage to your machine or property. 

THINK Safety! WORK Safely! Please read the following safety information carefully and follow the advice given to 
avoid  any  potential  dangers  to  yourself  and  others  or  damage  to  the  machine.  Special  safety  features  are 
incorporated in the design of the Finishing Mower for your protection. However, it can still be highly  dangerous 
to the careless operator. 

 

YOU are responsible for the SAFE operation and maintenance of your Finishing Mower.  YOU must ensure that 
you and anyone else, who is going to operate, maintain or work around the Finishing Mower be familiar with the 
operating, maintenance and safety procedures contained in this manual. 

 

DON’T 

let familiarity trap you into danger. 

DON’T 

allow riders on the Finishing Mower. 

SPECTATORS 

(particularly children) must be kept well away while operating as sticks and stones can fly further 

than you think. 

NEVER 

start or operate your Finishing Mower unless sitting on tractor seat. 

ALWAYS 

place all controls in neutral, lower machine, stop PTO and turn off engine before dismounting tractor. 

ALWAYS 

keep hands, feet, hair and clothing away from moving parts. 

DON’T 

attempt any adjustment whatsoever while the machine is operating or spinning. 

DON’T

 

attempt  to  clear  any  obstruction  around  the  machine  while  the  machine  is  operating  or  spinning  to  a 

stop. 

DON’T 

attempt to clear any obstruction from underneath the machine while the machine is operating   or spinning 

to a stop. 

DON’T 

operate your Finishing Mower whilst it is in the raised position. 

ALWAYS 

know  what  you  are  cutting.  Never  operate  in  an  area  that  has  hidden  obstacles.  Remove  all  sticks, 

stones, wire or other objects that might be hooked or snagged, causing injury or damage from the working  area 
before starting. 

MAKE REGULAR INSPECTION 

of cutter assembly for fracture and be sure that all blades and guards are properly 

attached.  Replace if any irregularity or excessive wear shows. 

NEVER 

exceed the limits of your Finishing Mower.   If 

it’s

 ability to do a job, or to do so safely is in question 

 

DON’T TRY

 IT

 

Summary of Contents for DK120










Reviews: