background image

Folded flap
to roll up

Pool blanket

Roller & Tube

Locate roller at opposite end of extended area - Fold over to roll up.

Tips to Save your Daisy

1)

  Whenever the cover is rolled up on 

the roller, ensure that the overcover is in 
place.

2)

  To prevent damage to your cover, 

do not drag the cover over abrasive pool 
decking or any sharp surfaces.

3)

  Excessive temperatures can 

damage your cover. Ensure that 
your pool does not reach excessive 
temperatures.

4)

  Most dirt and debris can be hosed 

orswept into your skimmer box. If you 
have a large amount of debris on top 
of your cover, a broom or brush can be 
used to sweep it into a pile for removal.  
Water and a soft brush are all that is 
required to remove heavier grime.

5)

  Before storage your cover should be 

thoroughly hosed both sides to remove 
any of the pool chemicals.  
When storing your solar pool cover, it 
can not be subjected to the sun. Store 
in a completely covered environment. 

6)

  When rolling up the cover onto 

the roller, ensure that it rolls up evenly. 
Always use your overcover whenever 
your cover is on the roller.

7)

  Test your water regularly to maintain 

correct chlorine levels. Your cover 
will deteriorate quicker when you 

have excessive chlorine. When super 
chlorinating, leave your cover off the 
pool for 48 hours. This allows your 
chlorine level to come back to normal.

8)

  Roll your cover over the top of your 

roller when using.

9)

  Fold in any flaps or step areas on 

the cover before rolling it up. This will 
ensure that you don’t put excessive 
force on the cover and allows it to move 
easily.

10)

  When putting the cover back onto 

the pool, roll the cover out slightly, fold 
one corner over onto itself (to create a 
bow effect), pick up the other corner 
and walk slowly down the side of your 
pool. 

(see cover image)

11)

  Do not sit or step on your roller. 

If the tube gets bent, it can not be 
repaired.

12)

  Monitor your chemical levels to 

maintain correct balance.

13)

 When using your roller, ensure that 

the brakes on the castors are locked.

14)

 If a storm is imminent, roll up the 

cover and store it safely.

OverCover

Once installed cover & roller  

are easy to move away.

Every roller comes with a  

Free Daisy OverCover.

Right - Overcover used  

when cover not on the pool.

ANY

 pool cover can be ruined in less 

than 

HALF

 of it’s predicted life span. 

95% of all warranty claims are not 
caused by product failure, but by owner 
abuse, caused by:

A)

  Leaving a cover rolled up out in the 

direct sunlight while off the pool.

OR

B)

  Having excess chlorine in the pool 

(either a little too high over a prolonged 
period or a lot too high over a very short 
period)

Either of these may  

VOID YOUR WARRANTY

To ensure the effective life of your pool 
cover please:

1 -

 

Ensure that your chlorine levels 

never exceed 3ppm. 

(Chlorine is a corrosive agent and 
actually wears the cover) and please 
do not assume that your salt-water 
chlorinator can control chlorine levels in 
your water.

TEST YOUR WATER REGULARLY.

2 -

 

Ensure that you take the cover off 

(and leave it off for 48 hours) when 
super chlorinating.

3 -

 

Never leave the cover folded or 

rolled up in the sun. It must be in full 
shade. (Not under shade cloth)

This will cause the cover to be damaged 
in strips across the cover and will cause 
delamination,also the sun and heat will 
cause corrosive wear.

4 -

 

Do not cover the blanket with a 

tarpaulin or anything other than the 
recommended cover type.

This material will reflect the sun’s rays 
while many others will absorb them.

5 -

 

When storing the cover ensure 

that it has been washed on both 
sides with fresh water before storage. 

This does not apply if you are replacing 
the cover within 24 hours. This prevents 
the chlorine residue from burning the 
cover.

6 -

 

If you have a roller ensure that 

you place the white overcover 
(supplied with the roller) over the 
cover every time you roll up the 
cover, even if the swim is only for 10 
minutes, as this is enough time to 
destroy the cover. 

Overheating on the roller will  

cause delamination in strips across  

the cover and in extreme cases can 

cause the material to become  

molten and weld itself to itself

Defective material or workmanship on 
a pro-rata basis as set out on the back 
page. The manufacturer will repair or 
replace the product upon inspection at 
their premises.

WITHOUT PROPER CARE

Reviews: