background image

English

8

(6) Hook the indoor unit onto the installation panel. (Refer to Fig. 9)

Placing buffering material between the wall and the indoor unit at this time will make work easier.

For right, bottom-right, and back-right piping

Pass the drain hose and the refrigerant piping to the wall.

(7) Pass power supply wiring, transmission wiring, ground wiring, and remote controller wiring 

through the wiring guide in through the back of the indoor unit and to the front.

(8) Connect the piping. (See “5.REFRIGERANT PIPING WORK” and Fig. 10)

To avoid the influence of noise from the power supply line on the transmission wiring and the remote 
controller wiring, these wirings must be kept as far as possible from the power/ground wirings. As shown in the 
figure, keep the power supply wiring and the ground wiring together. Keep the transmission and remote con-
troller wirings together and route them maintaining a good distance from the power supply/ground wirings 
(that is, on the other side of the power supply/ground wirings). Then, fix them securely on the refrigerant pipe.

Seal the piping through-hole with putty corking material.

(9) Push on both bottom edges of the indoor unit using both hands and hook the tab on the back of 

the indoor unit onto the installation panel (1). (Refer to Fig. 9)

At this time remove the buffering material placed in step (6).

Refrigerant piping

Be sure to pass all wires through 
the wiring guide.

Tab

(There are 2 places.)

Wiring (locally procured)

Power supply wiring, Transmission wiring, Ground wiring, 
Remote controller wiring

Wall

Installation panel 
(accessory) (1)

Front panel

Front grill

Service lid

Place buffering material

Hook the indoor unit hook onto the installation panel (1).

Fig. 9

Secure with 
vinyl tape.

Wrap the insulating tape overlapping at least half the width with 
each wrap. 
Wrap the insulating tape all the way to the L-shaped bend.

Seal with putty corking 
material.

Drain hose

Wiring

Fig. 10

Refrigerant piping

A

A

 arrow view

Power supply wiring and 
ground wiring

Refrigerant piping

Transmission wiring and 
remote controller wiring

01_EN_3P156215-10P.fm  Page 8  Wednesday, April 2, 2008  11:47 AM

Summary of Contents for VRV FXAQ20MAVE























Reviews: