background image

Installation manual

5

VAM350~2000FC

Total Heat Exchanger

HRV (Heat Reclaim Ventilation)

4P415947-1A – 2017.08

System configuration

Independent system

Air conditioner linked operation system 

System

Standard method

Related items in 

Electric wiring

Independent system

• Up to 16 units can be controlled with the 

remote controller for HRV. (A system with 
two remote controls can be created in the 
master/slave switching.)

• All HRV operations can be used and 

indicated.

• Operation monitor output and humidifier 

operation are possible using Adapter 
PCB.

• Remote control cord should be procured 

locally.

 

(Maximum cord length: 500 m)

"When connecting to 

Remote controller for 

HRV" on page 16

Combined 

operation system 

with VRV systems 
and Sky-air series

1-group linked 

operation system

• A combined total of up to 16 air 

conditioners and the HRV can be 
controlled.

• The HRV ventilation mode can be 

operated independently when air 
conditioners are not being used.

• Using the local setting of the remote 

controller for air conditioners, various 
settings such as precool/pre-heat 
reservation on/off, ventilation flow rate, 
ventilation mode, etc.

"Standard 1-group 

linked-control 

system" on page 16

Multi-group 

(2 or more) linked 

operation system

• Since all VRV units are connected to a 

single line in view of installation, all VRV

 

units are subjects for operation.

• If there are problems operating all VRV

 

units, do not use this system.

"Linked control with 

more than two 

groups" on page 17

HRV

HRV

1

2

1

Remote controller 
for HRV

2

2-wire cord 
(produced locally)

VRV

HRV

1

2

1

Remote controller 
for air conditioner

2

Remote controller 
for air conditioner

VRV

VRV

VRV

VRV

HRV

HRV

1

2

5

5

5

5

3

4

6

1

Group 1

4

Group 4

2

Group 2

5

Remote controller 
for VRV

3

Group 3

6

Distant control 
adapter

NOTE

Adapter PCB for external input/output: BRP4A50A; Distant control adapter: KRP2A51 (installation box: KRP1B101).

Operation of two or more groups is not possible with direct duct connection.

With VAM types, the direct duct connection shown can also be selected for 1-group operation systems.

System

Standard method

Related items in 

Electric wiring

Direct duct connection system

• The HRV will operate only when the air 

conditioner fan is on.

• Other specifications are the same as 

those of the standard system.

"Direct duct 

connection system 

for 1-group operation 

system" on page 17

VRV

HRV

1

2

3

1

Remote controller 
for air conditioner

2

Remote controller 
for air conditioner

3

Duct

Summary of Contents for VAM350FC






























Reviews: