background image

3

English

Outdoor Unit Installation Drawings

Wrap the insulation pipe with 
the finishing tape from bottom 
to top.

In sites with poor drainage, use 
block bases for outdoor unit.  
Adjust foot height until the unit 
is leveled.  Otherwise, water 
leakage or pooling of water may 
occur.

574

(Foot bolt-hole centres)

(From unit's side)

105.5

Where there is a danger of the unit 
falling, use foot bolts, or wires.

Foot bolt-hole 

centres

311

Allow space for piping 
and electrical servicing.

250mm from wall

unit: mm

O.D. 9.5mm

Gas pipe

Liquid pipe

O.D. 6.4mm

20g/m

15m

20m

Max. allowable length

Max. allowable height

Additionl refrigerant
required for refrigerant
pipe exceeding
10m in length.

*

 Be sure to add the proper amount of additional refrigerant.

   Failure to do so may result in reduced perfomance.

How to remove the stop 
valve cover.

Remove the screw on the 
stop valve cover.
Slide the lid downward 
to remove it.

How to attach the stop 
valve cover.

Insert the upper part of 
the stop valve cover into the 
outdoor unit to install.
Tighten the screws.

Stop valve cover

01_EN_3P182455-1.fm  Page 3  Wednesday, May 17, 2006  5:37 PM

Summary of Contents for RKS20E2V1B















Reviews: