Daikin REMQ120PTJU, Engineering Data

Page: 8 / 58

EDUS39-802A-R2 Dimensions
REYQ-P Heat Recovery (208-230V) 7
REYQ168, 192, 216, 240PTJU
Model Name
or more
Outdoor Unit 1
19-11/16
11-13/16 or more
< Suction side >
(Foundation bolt hole)
19-11/16 or more
59-1/16 h 2
< Front >
(Pitch of foundation bolt holes)
(Pitch of foundation
bolt holes)
(Pitch of foundation bolt holes)
Drawing No.
(Foundation bolt hole)
Outdoor Unit 2
Drawing No.
(Front)
3D058616 3D058616 3D058616 3D058617 3D058616 3D058617 3D058617 3D058617 3D058617 3D058617 3D058616 3D058616 3D058616 3D058616 3D058617 3D058617 3D058616 3D058617
RXYQ72PTJU RXYQ96PYDN REMQ120PYDN REMQ72PTJU REMQ120PTJU RXYQ72PYDN RXYQ120PYDN RXYQ96PTJU REMQ72PYDN RXYQ72PTJU REMQ96PYDN REMQ72PTJU RXYQ72PYDN REMQ72PYDN RXYQ120PTJU REMQ72PYDN RXYQ72PYDN REMQ96PTJU
h 1
REMQ120PYDN RXYQ120PTJU RXYQ120PYDN REMQ120PTJU RXYQ72PYDN RXYQ120PYDN REMQ120PTJU RXYQ120PTJU RXYQ120PTJU REMQ120PYDN RXYQ96PYDN REMQ72PYDN REMQ96PTJU REMQ96PYDN REMQ120PYDN RXYQ96PTJU REMQ120PTJU RXYQ120PYDN
REYQ216PYDN REYQ240PTJU RXYQ216PTJU RXYQ168PTJU REYQ168PYDN RXYQ192PYDN REYQ216PTJU REYQ144PYDN RXYQ192PTJU REYQ192PYDN REYQ240PYDN RXYQ144PYDN REYQ168PTJU RXYQ240PYDN RXYQ240PTJU RXYQ168PYDN REYQ192PTJU RXYQ216PYDN
3D058616 3D058616 3D058616 3D058616 3D058616 3D058616 3D058616 3D058616 3D058616 3D058617 3D058617 3D058617 3D058617 3D058617 3D058617 3D058617 3D058617 3D058617
4-19/32×7/8-mm-Oblong holes
30-1/8
Outdoor Unit 1
36-5/8
25/32 or more
Outdoor Unit 2
25/32
66-1/8
31-3/16
Notes : 1. Heights of walls Front : 59-1/16in Suction side : 19-11/16in Side : Height unrestricted The installation space shown in this figure is based on the condition of cooling operation at the outdoor air temperature of 95˚F. The installation space of suction side shown above must be expanded in the following case. · Design outdoor temperature becomes over 95˚F. · Operating over Max. operating load (In case of causing a heavy heating load at indoor unit side) 2. If the above wall heights are exceeded then h2/2 and h1/2 should be added to the front and suction side service spaces respectively as shown in the following figure. 3. When installing the units the most appropriate pattern should be selected from those shown above in order to obtain the best fit in the space available always bearing in mind the need to leave enough room for a parson to pass between units and wall and for the air to circulate freely. (If more units are to be installed than are catered for in the above patterns your layout should take account of the possibility of short circuits. ) 4. The units should be installed to leave sufficient space at the front for the on site refrigerant piping work to be carried out comfortably.
36-5/8
13/32 or more
28-7/16 ~ 29-1/32
4-19/32 × 7/8-mm-Oblong holes
31-3/16
13/32 or more
3D059677