manualshive.com logo in svg

Daikin MICROTECH 4, Operating Manual

Share
Download
Daikin MICROTECH 4 Operating Manual Download Page 56

 

 

 

 

 
 

D

–EOMWC00A07-16_02EN 

Operation Manual

 

56/77 

 

10.8.15 

Condenser Pressure Sensor Fault 

This alarm indicates that the condensing pressure transducer is not operating properly.  
 

Symptom

 

Cause

 

Solution

 

Circuit status is Off. 
The circuit is stopped. 
Bell icon is 

moving on controller’s 

display. 
String in the alarm list: 

CxCmp1 CondPressSen 

String in the alarm log: 

CxCmp1 CondPressSen 

String in the alarm snapshot 

CxCmp1 CondPressSen 

Sensor is broken. 

Check for sensor integrity. Check 
correct sensors operation 
according information about mVolt 
(mV) range related to pressure 
values in kPa. 

Sensor is shorted. 

Check if sensor is shorted with a 
resistance measurement. 

Sensor is not properly connected 
(open). 

Check for correct installation of the 
sensor on refrigerant circuit pipe. The 
transducer must be able to sense the 
pressure through the valve’s needle. 
Check for absence of water or 
humidity on sensor electrical 
contacts. 
Check for correct plug-in of the 
electrical connectors. 

 

 

Check for correct sensors wiring also 
according electrical scheme. 

Reset 

 

Notes 

Local HMI 
Network 
Auto 





 

10.8.16 

Motor Temperature Sensor Fault 

This alarm is generated to indicate that the sensor is not reading properly. 
 

Symptom 

Cause 

Solution 

Circuit status is Off. 
The circuit is switched off with the 
normal shutdown procedure. 
Bell icon is moving on controller’s 
display. 
String in the alarm list: 

CxCmp1 OffMtrTempSen 

String in the alarm log: 

CxCmp1 OffMtrTempSen 

String in the alarm snapshot 

CxCmp1 OffMtrTempSen 

 

Sensor is shorted. 

Check for sensor integrity. 

Check correct sensors operation 
according information acceptable 
resistance range related to 
temperature values. 

Sensor is broken. 

Check if sensor is shorted with a 
resistance measurement. 

Sensor is not good connected (open).  Check for absence of water or 

humidity on sensor electrical 
contacts. 

Check for correct plug-in of the 
electrical connectors. 
Check for correct sensors wiring also 
according with electrical scheme. 

Reset 

 

Notes 

Local HMI 
Network 
Auto 

 
 
 

 

 

 

Summary of Contents for MICROTECH 4














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands