manualshive.com logo in svg

Daikin MICROTECH 4, Operating Manual

Share
Download
Daikin MICROTECH 4 Operating Manual Download Page 34

 

 

 

 

 
 

D

–EOMWC00A07-16_02EN 

Operation Manual

 

34/77 

 

9 

SOFTWARE OPTIONS 

For  the  EWWD 

–  EWWH  –  EWWS  units,  the  possibility  to  employ  a  set  of  software  options  has  been  added  to  the 

functionality of the chiller, in according with the new Microtech 4 installed on the Unit. The Software Options do not require 
any additional hardware and regard communication channels 

During the commissioning the machine is delivered with the Option Set chosen by the customer; the Password inserted is 
permanent  and  depends  on  the  Serial  Machine  Number  and  the  Option  Set  selected.  In  order  to  check  the  current 
Option Set: 

 

Main Menu 

→ 

Commission Unit 

→

 Software Options

 

 

 

Parameter

 

Description

 

Password 

Writable by Interface/Web Interface 

Option Name 

Option Name 

Option Status 

Option is activated 

Option is not activated 

 

The Current Password inserted activates the selected options. 

The Option Set and the Password are updated in the Factory. If the customer wants to change its Option Set, he  needs to 
contact the Daikin Personnel and asks for a new password.  

As soon as the new password is communicated, the follow steps allow the customer to change the Option Set by himself:  

1.  Wait for the circuits are both OFF, then, from the Main Page,  

9.1.1 

Go to Main Menu 

→ Commission Unit → Software Options 

2.  Select the Options to Activate 
3.  Insert the Password 
4.  Wait for the States of the selected options going to On  
5.  Apply Changes

→Yes (it will reboot the controller) 

 

The Password is changeable only if the machine is working in safe conditions: both the circuits 
are in the State Off.

 

9.2 

Inserting the Password in a Spare Controller 

If the Controller is broken and/or it needs to be replaced for any reason, the customer needs to configure the Option Set 
with a new Password. 
If this replacement is scheduled, the customer can ask to Daikin Personnel for a new Password and repeat the steps in 
chapter 4.15.1. 
If there is no enough time to ask for a Password to Daikin Personnel (ex. an expected failure of the controller), a set o f 
Free Limited Password is provided, in order not to interrupt the machine’s working. 
These Passwords are free and visualized in: 

 

Summary of Contents for MICROTECH 4














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands