background image

  English / 

8

Care and Cleaning

WARNING

During maintenance you must stop the oper-
ation and remove the power plug from the 
electrical outlet.

Electric shock or injury may occur.

CAUTION

Do not wash the main unit with water.

If water gets inside the unit, electric shock or malfunc-
tion may occur.

ATTENTION

Be careful not to scratch the 
front or damage the rear protru-
sions of the removed front 
panel

.

In particular, the rear protru-
sions function as a safety switch 
to turn OFF the power if the front 
panel is opened.
If damaged, the unit will not 
operate.

NOTE

If the front panel is not correctly set on the main unit, 
the unit will not operate.

Cleaning the pre-filter

Target is once every 2 weeks

1. Remove the front panel.

Hold the panel removal knobs (two locations, left and right) and 
pull the panel toward you raising it up.

2. Remove the pre-filter.

While holding down the plasma ionizer pull the upper portion 
toward you and lift it upward.

3. Clean the pre-filter.

After using a vacuum cleaner to remove any dust, clean with 
water.

If it is very dirty, use a soft brush or a neutral cleaner to clean then 
dry well in the shade.

CAUTION

Do not dry at a location directly exposed to the sun.

Do not clean with water hotter than 50 

°

C.

Do not burn with fire.
Color changes or deformation may occur and the unit may become 
unusable.

4. Install the pre-filter in its original position.

Match the lower edge of the pre-filter to the knob of the plasma 
ionizer and then insert the hole at the top into the protrusion of the 
plasma ionizer.

5. Mount the front panel to the main unit.

(1) Hang the hooks (two) at the top of the front panel on the 

grooves of the top of the main unit.

(2) Hold the panel removal knobs (two locations, left and right) and 

press into the main unit.

Rear side

Protrusion

Front panel

Knob 
(2 locations, 
left and right)

Protrusion (6 

locations)

Hook (2 

locations)

Hole (6 

locations)

Protrusion (6 

locations)

Hook (2 

locations)

Hole (6 

locations)

Hook 
(2 locations)

Summary of Contents for MC704AVM















Reviews: