background image

  English / 

6

3. Install the Titanium apatite photocatalytic filter roll.

(1) Cut off one piece along the perforation.

(2) Place the dark colored surface facing up and then correctly 

insert into the hooks (four) of the plasma ionizer.

CAUTION

If the front surface and rear surface of the filer are mistaken, the per-
formance will drop.

(3) Store the remaining Titanium apatite photocatalytic filter roll in 

the Titanium apatite photocatalytic filter roll receiver.

ATTENTION

The Titanium apatite photocatalytic filter roll can also be set without 
being cut.
(1) Store the remaining Titanium apatite photocatalytic filter roll in 

the Titanium apatite photocatalytic filter roll receiver.

(2) Correctly insert into the holes (four) of the Titanium apatite 

photocatalytic filter roll into the hooks (four).

4. Install the plasma ionizer in its original configuration.

5. Mount the front panel to the main unit.

(1) Hang the hooks (two) at the top of the front panel on the 

grooves of the top of the main unit.

(2) Hold the panel removal knobs (two locations, left and right) and 

press into the main unit.

NOTE

If the front panel is not correctly set on the main unit, the unit will not 
operate.

Installation of main unit

Follow the standards below during installation.

〈〈〈〈

If installed on a table

〉〉〉〉

〈〈〈〈

If installed on a wall

〉〉〉〉

Ask your dealer for a 

wall-hanging kit (sold separately)

.

NOTE

If hanging the unit on a wall, make sure the wall is sufficiently strong 
and has a pillar behind it.

ATTENTION

If operated outside the conditions shown below, malfunction may 
occur.

Indoor temperature 0 - 32 

°

C

Indoor humidity 80% or less

Titanium apatite 
photocatalytic filter roll

Hole

Hole

Hole

Hole

Hook

Hook (4 locations)

Dark colored 
surface

Titanium apatite 
photocatalytic 
filter roll

Hole (4 locations)

Dark colored 
surface

Titanium apatite 
photocatalytic filter roll

Titanium apatite 
photocatalytic 
filter roll

Hole

Hook

Hook 
(4 locations)

Hook 
(2 locations)

Min. 100cm

Min. 50cm

Min. 50cm

Min. 10cm

Summary of Contents for MC704AVM















Reviews: