background image

Installation manual

3

20B7Y1R

Air cooled refrigeration condensing unit

4P360438-1B – 2014.01

2. BEFORE INSTALLATION

CAUTION

• When installing the indoor unit, refer to the installation manual 

provided for the indoor unit.

• Use the outdoor unit multi-connection piping kit(EKHRQZM) to 

split up the gas piping and connect it to the different outdoor units.

• Optional accessories are required for the installation of the 

product. Refer to the information on optional accessory.

2-1 Standard supplied accessories

The following accessories are included. The storage location of the 
accessories is shown in the figure.

Note

Do not throw away any of the accessories until installation is complete.

Miscellaneous

• Installation manual
• Operation manual
• Refrigerant label
• Refrigerant oil label

2-2 Mandatory connection kit

Outdoor unit multi-connection piping kit.

2-3 Model series

LREQ15-20

2-4 Example of system configuration

1

Operation manual 

2

Installation manual 

3

Clamps

4

Accessory pipes (Installed on bottom frame)

2-5 Indoor unit constraints

• Install an R410A mechanical thermostatic expansion valve on 

each indoor unit.

• Insulate the feeler block of the mechanical thermostatic expansion 

valve.

• Install an R410A solenoid valve (Max. operating differential 

pressure of 3.5 MPa [35 bars] or over) on the primary side of the 
mechanical thermostatic expansion valve described above for 
each indoor unit.

• Install a filter on the primary side of the solenoid valve described 

above for each indoor unit. Determine the filter mesh count based 
on the size specified by the solenoid valve and mechanical 
thermostatic expansion valve being used.

• Route the path to the indoor unit heat exchanger so that the flow of 

refrigerant is from top to bottom.

• When installing a number of indoor units, be sure to install them at 

the same level.

• Use either off-cycle defrosting or electric heater defrosting as the 

defrosting type. Hot-gas defrosting models cannot be used.

• Make sure the total internal volume of indoor units connected to the 

condensing units is 80 l or lower.

• Starting from an outdoor temperature of 32°C, the total indoor unit 

capacity needs to be 50% or more of the total outdoor unit capacity.

3. SELECTION OF LOCATION

Select a location for installation that meets the following conditions. 
Get the customer’s permission.

1.

There is no danger of fire due to leakage of inflammable gas.

2.

Select the location of the unit in such a way that neither the 
discharged air nor the sound generated by the unit disturb anyone.

3.

The foundation is strong enough to support the weight of the unit 
and the floor is flat to prevent vibration and noise generation.

4.

The piping length between the outdoor unit and the indoor unit may 
not exceed the allowable piping length. 
(Refer to

 

"6. REFRIGERANT PIPING" on page 6

)

5.

Locations where the unit’s suction vent and outlet vent do not 
generally face the wind. 
Wind blowing directly into the suction or outlet vents will interfere 
with the unit’s operation.
If necessary, install some kind of obstruction to block the wind.

6.

The space around the unit is adequate for servicing and the 
minimum space for air inlet and air outlet is available. 
(See the 

"Installation Space Examples" on page 4

 for the minimum 

space requirements.)

Name Clamp (1) Clamp (2)

Liquid side 

accessory 

pipe (1)

Liquid side 

accessory 

pipe (2)

Gas side 

accessory 

pipe (1)

Quan-

tity

10 pcs.

2 pcs.

1 pc.

1 pc.

1 pc.

Shape

Small

Name

Gas side 

Branch pipe 

(1)

Gas side 

Branch pipe 

(2)

Gas side 

Branch pipe 

(3)

Gas side 

Branch 

pipe (4)

Sight glass

Quantity

1 pc.

2 pc.

2 pc.

2 pc.

1 pc.

Shape

Name

Outdoor unit

Indoor unit

Unit cooler

Showcase

Shape

Name

Indoor unit

Control panel 

(Defrost)

Warning 

panel

Unit cooler

Showcase

Shape

1, 2, 3

4

LREQ15, LREQ20

Summary of Contents for LREQ15B7Y1R





























Reviews: