background image

Installation manual

1

20B7Y1R

Air cooled refrigeration condensing unit

4P360438-1B – 2014.01

CONTENT

 1. INTRODUCTION ....................................................................... 1

 1-1 Safety precautions ............................................................. 1
 1-2 Special notice of product.................................................... 2
 1-3 Disposal requirements ....................................................... 2

 2. BEFORE INSTALLATION.......................................................... 3

 2-1 Standard supplied accessories .......................................... 3
 2-2 Mandatory connection kit ................................................... 3
 2-3 Model series....................................................................... 3
 2-4 Example of system configuration ....................................... 3
 2-5 Indoor unit constraints........................................................ 3

 3. SELECTION OF LOCATION ..................................................... 3
 4. HANDLING THE UNIT .............................................................. 6
 5. PLACING THE UNIT ................................................................. 6
 6. REFRIGERANT PIPING............................................................ 6

 6-1 Selection of piping material................................................ 7
 6-2 Protection against contamination when installing pipes..... 8
 6-3 Pipe connection ................................................................. 8
 6-4 Connecting the refrigerant piping....................................... 8

 7. FIELD WIRING ........................................................................ 13

 7-1 Example of wiring entire system ...................................... 13
 7-2 Procedure for incoming wiring ......................................... 14
 7-3 Procedure for power supply wiring................................... 14
 7-4 Procedure for wiring inside units...................................... 16

 8. INSPECTION AND PIPE INSULATION .................................. 16

 8-1 Airtight test/refrigerant oil charging/vacuum drying.......... 16
 8-2 Thermal insulation work ................................................... 18
 8-3 Checking of device and installation conditions ................ 18

 9. CHECKS AFTER WORK COMPLETION................................ 18
 10. REFRIGERANT REPLENISHMENT ....................................... 19
 11. FIELD SETTINGS ................................................................... 20
 12. TEST RUN............................................................................... 21

The English text is the original instruction. Other languages are 
translations of the original instructions.

1. INTRODUCTION

• This document is an installation manual for the Daikin Air Cooled 

Refrigeration Condensing Unit. Before installing the unit, read this 
manual thoroughly, and following the instructions contained in it. 
After installation, do a test run to make sure the unit runs properly, 
and then explain how to operate and take care of the unit to the 
customer, using the operation manual.

• Lastly, make sure the customer keeps this manual, along with the 

operation manual, in a safe place.

• This manual does not describe how to install the indoor unit. 

Refer to the installation manual included with the indoor unit for 
that.

1-1 Safety precautions

Please read these “Safety precautions” carefully before installing 
condensing unit and be sure to install it correctly. 
Meaning of WARNING and CAUTION notices
Both are important notices for safety. Be sure to follow them.

WARNING

.... Failure to follow these instructions properly may 

result in personal injury or loss of life.

CAUTION

..... Failure to observe these instructions properly 

may result in property damage or personal injury, 
which may be serious depending on the circum-
stances.

After completing installation, conduct a test operation to confirm that 
the equipment operates without any problems. Then, explain to the 
customer how to operate the equipment and take care of it following 
the operation manual. 

Ask the customer to store the installation manual along with the 
operation manual for future reference.

WARNING

• Ask your dealer or qualified personnel to carry out installation work. 

Do not attempt to install the condensing unit yourself. Improper 
installation may result in water leakage, electric shocks or fire.

• Install the condensing unit in accordance with the instructions in 

this installation manual. 
Improper installation may result in water leakage, electric shocks or fire.

• When installing the unit in a small room, take measures so that the 

refrigerant may not exceed the limiting concentration in the event 
of refrigerant leakage.
Contact your dealer for further information. If the refrigerant leaks and 
exceeds the limiting concentration, it may lead to oxygen deficiency.

• Be sure to use only the specified accessories and parts for 

installation work. 
Failure to use the specified parts may result in the unit falling, water 
leakage, electric shocks or fire.

• Install the condensing unit on a foundation strong enough to 

withstand the weight of the unit. 
If a foundation does not have sufficient strength, the equipment 
may fall and cause injury.

• Carry out the required installation work in consideration of strong 

winds, typhoons or earthquakes.
If the installation work is not properly carried out, the unit may fall 
down and cause accidents.

• The electrical work must be carried out by the qualified electrician in 

accordance with the local laws and regulations and this installation 
manual. Make sure to provide a dedicated power supply circuit and 
never connect additional wiring to the existing circuit.
An insufficient power supply capacity or improper electrical work 
may lead to electric shocks or fire.

• Be sure to earth the condensing unit. 

Do not earth the unit to a utility pipe, lightning conductor or 
telephone earth lead. Imperfect earthing may result in 
electric shocks or fire. 
A high surge current from lightning or other sources may cause 
damage to the condensing unit.

• Be sure to install an earth leakage breaker.

Failure to install an earth leakage breaker may result in electric 
shocks or fire.

• Be sure to switch off the unit before touching any electrical parts.

Touching a live part may result in electric shock.

• For wiring, use the specified wires and connect and fasten them 

firmly so that no external force from the wires may be applied to the 
terminal connections.
If the wires are not firmly connected and fastened, it may cause 
heating, fire or the like.

• When wiring the power supply and connecting transmission wiring, 

position the wires so that the control box lid can be securely fastened. 
Improper positioning of the control box lid may result in electric 
shocks, fire or the terminals overheating.

• If refrigerant gas leaks during installation, ventilate the area 

immediately. 
Toxic gas may be produced if the refrigerant comes into contact 
with fire.

• After completing installation, check for refrigerant gas leakage. 

Toxic gas may be produced if the refrigerant gas leaks into the 
room and comes into contact with a source of fire, such as a fan 
heater, stove or cooker.

• Do not directly touch refrigerant that has leaked from refrigerant 

pipes or other areas, as there is a danger of frostbite.

• Do not allow children to climb on the outside unit and avoid placing 

objects on the unit.
Injury may result if the unit becomes loose and falls.

LREQ15B7Y1R
LREQ20B7Y1R

Air cooled refrigeration condensing unit

Installation manual

Summary of Contents for LREQ15B7Y1R





























Reviews: