background image

English

4

3. OPTIONAL ACCESSORIES

The optional decoration panel and remote controller are required for this indoor unit. (Refer to Table 1, 2)
(However, the remote controller is not required for the slave unit of a simultaneous operation system.)

Table 1

These are two types of remote controllers: wired and wireless. Select a remote controller from Table 2 
according to customer request and install in an appropriate place.

Table 2

NOTE

If you wish to use a remote controller that is not listed in “Table 2” on page 4, select a suitable remote con-
troller after consulting catalogs and technical materials.

FOR THE FOLLOWING ITEMS, TAKE SPECIAL CARE DURING CONSTRUCTION AND 
CHECK AFTER INSTALLATION IS FINISHED.

1. Items to be checked after completion of work

2. Items to be checked at time of delivery

* Also review the “1. SAFETY PRECAUTIONS”

Unit model

Optional decoration panel

FXFQ25 · 32 · 40 · 50 · 63 · 80 · 100 · 125PVE

BYCP125K-W1

Color : Fresh white

Remote controller

Wired type

BRC1C62

Wireless type (Heat pump type/Cooling only type)

BRC7F634F/BRC7F635F

Items to be checked

If not properly done, what is likely to occur

Check

Are the indoor unit and outdoor unit fixed 
firmly?

The unit may drop, vibrate or make noise.

Is the outdoor unit fully installed?

The unit may malfunction or the compo-
nents burn out.

Is the gas leak test finished?

It may result in insufficient cooling.

Is the unit fully insulated?

Condensate water may drip.

Does drainage flow smoothly?

Condensate water may drip.

Does the power supply voltage correspond 
to that shown on the name plate?

The unit may malfunction or the compo-
nents burn out.

Are wiring and piping correct?

The unit may malfunction or the compo-
nents burn out.

Is the unit safely grounded?

It may result in electric shock.

Is wiring size according to specifications?

The unit may malfunction or the compo-
nents burn out.

Is something blocking the air outlet or inlet 
of either the indoor or outdoor units?

It may result in insufficient cooling.

Are refrigerant piping length and additional 
refrigerant charge noted down?

The refrigerant charge in the system is not 
clear.

Items to be checked

Check

Are the terminal box lid, air filter, suction grille attached?

Did you explain about operations while showing the instruction manual to your customer?

Did you hand the instruction manual over to your customer?

01_EN_3P161684-4E.fm  Page 4  Monday, August 16, 2010  7:11 PM

Summary of Contents for FXFQ25PVE



























Reviews: