background image

21

Please check again before calling a repair person.

Check again.

Case

Check

The air conditioner does not 
operate.
(OPERATION lamp is off.)

• Hasn’t a breaker turned OFF or a fuse blown?
• Isn’t it a power failure?
• Are batteries set in the remote controller?
• Is the timer setting correct?

Cooling (Heating) effect is poor.

• Are the air filters clean?
• Is there anything to block the air inlet or the outlet of the 

indoor and the outdoor units?

• Is the temperature setting appropriate?
• Are the windows and doors closed?
• Are the air flow rate and the air direction set appropriately?

Operation stops suddenly.
(OPERATION lamp flashes.)

• Are the air filters clean?
• Is there anything to block the air inlet or the outlet of the 

indoor and the outdoor units?
Clean the air filters or take all obstacles away and turn the 
breaker OFF. Then turn it ON again and try operating the air 
conditioner with the remote controller. If the lamp still flashes, 
call the service shop where you bought the air conditioner.

An abnormal functioning
happens during operation.

• The air conditioner may malfunction with lightning or radio 

waves. Turn the breaker OFF, turn it ON again and try 
operating the air conditioner with the remote controller.

01_EN_3P232468-8.fm  Page 21  Wednesday, June 4, 2008  10:33 AM

Summary of Contents for FTYN25DV1A



























Reviews: