background image

14

POWERFUL Operation

POWERFUL operation quickly maximizes the cooling 
(heating) effect in any operation mode. You can get the 
maximum capacity. 

To start POWERFUL 
operation

1. Press “POWERFUL button”.

• POWERFUL operation ends in 20 minutes. 

Then the system automatically operates 
again with the settings which were used 
before POWERFUL operation.

• When using POWERFUL operation, 

there are some functions which are not 
available.

• “

” is displayed on the LCD.

To cancel POWERFUL 
operation

2. Press “POWERFUL button” 

again.

• “

” disappears from the LCD.

NOTE

Notes on POWERFUL operation

• POWERFUL Operation can only be set when the unit is running. Pressing the operation 

stop button causes the settings to be canceled, and the “

” disappears from the LCD. 

Priority is given to the function of whichever button is pressed last.

In COOL and HEAT mode

To maximize the cooling (heating) effect, the air flow rate is fixed to the maximum setting.
The temperature and air flow settings are not variable.

In DRY mode

The air flow rate is slightly increased.

In FAN mode

The air flow rate is fixed to the maximum setting.

1, 2

01_EN_3P232468-8.fm  Page 14  Wednesday, June 4, 2008  10:33 AM

Summary of Contents for FTYN25DV1A



























Reviews: