background image

6

English

Preparation before Installation

3.

How to set the different addresses

When two indoor units are installed in one room, 
the two wireless remote controllers can be set 
for different addresses. 

1) Remove the metal plate electrical wiring 

cover. 
(Refer to the 

When connecting to an HA 

system

.)

2) Cut the address jumper (JA) on the printed 

circuit board.

3) Cut the address jumper (J4)  in the remote 

controller.

4.

When connecting to an HA system 
(wired remote controller, central remote controller etc.)

1) Remove the front grille. (3 screws)
2) Remove the electrical wiring box. (1 screw)
3) Remove the metal plate electrical wiring cover. (4 tabs)
4) Attach the connection cord to the S21 connector and pull the harness out through the notched part in the figure.
5) Replace the electrical wiring cover as it was,  and pull the harness around, as shown in the figure.
* Some models cannot be connected to an HA system. 

Refrigerant Piping Work

1.

Flaring the pipe end 

1) Cut the pipe end with a pipe cutter.
2) Remove burrs with the cut surface facing downward 

so that the chips do not enter the pipe.

3) Put the flare nut on the pipe.
4) Flare the pipe.
5) Check that the flaring is properly made.

WARNING

• Do not use mineral oil on flared part.
• Prevent mineral oil from getting into the system as this would reduce the lifetime of the units.
• Never use piping which has been used for previous installations. Only use parts which are delivered with the unit.
• Never install a drier to this R410A unit in order to guarantee its lifetime.
• The drying material may dissolve and damage the system.
• Incomplete flaring may cause refrigerant gas leakage.

ADDRESS

J4

EXIST

1

 CUT

2

J4

Address

JA

Address

JA

EXIST

1

CUT

2

Screw

HA cord

HA connector
(S21)

Tab

Tab

Push

Slide

Push

Metal plate 
electrical cover

Tab

Push

Main body

Notched part

4)

5) Replace the electrical 

wiring cover as it was,  
and pull the harness 
around, as shown 
in the figure.

Attach the connection cord to 
the S21 connector and pull the 
harness out through the 
notched part in the figure.

3) Remove the metal 

plate electrical 
wiring cover.

Set exactly at the position shown below.

A

Flaring

Die

A 0-0.020 inch (0-0.5mm)

Clutch-type

Flare tool for R410A

0.039-0.059 inch (1.0-1.5mm)

Clutch-type (Rigid-type)

0.059-0.079 inch (1.5-2.0mm)

Wing-nut type (Imperial-type)

Conventional flare tool

(Cut exactly at 

right angles.)

 Remove burrs.

Check

Flare’s inner surface 
must be flaw-free.

The pipe end must 
be evenly flared in a 
perfect circle.

Make sure that the 
flare nut is fitted.

01_EN_3P276866-2D.fm  Page 6  Friday, February 18, 2011  4:07 PM

Summary of Contents for FTXN15KVJU















Reviews: