background image

Operation Manual

ED12-011A

98

Room Air Conditioners SUPER MULTI H-Series

14

Air filter

Air purifying

filter frame

Hold the recessed 
parts of the frame and 
unhook the four claws.

CAUTION

Before cleaning, be sure to stop the operation and
turn the breaker OFF.

Open the front grille.

l

Hold the grille by the tabs on the two sides and lift it
unitl it stops with a click. (about 60˚)

Pull out  the air filters.

l

Push a little upwards the tab
at the center of each air filter,
then pull it down.

1

3

2

Take off  the  air  purifying  filters  and
clean them.

l

Wash them with water, or
clean them with a vacuum
cleaner.

l

If the dust does not come
off easily, wash them with
neutral detergent thinned
with lukewarm water, then
dry them up in the shade.

Care and Cleaning

Set the air purifying filters and the air
filters as the y were  and  close  the  front
grille .

4

NOTE

l

In a dusty environment, clean the air filters at least once
in every two weeks even before the cleaning lamp lights
up.

l

Operation with dusty air filters lowers the cooling and
heating capacity and wastes energy.

Cleaning the indoor and outdoor
units and the remote controller

NOTE

l

To order air purifying filters, contact the service shop where
you bought the air conditioner.

l

Once the air purifying filter element gets dirty, it is not
reusable but must be thrown away.

l

Operation with dirty air purifying filters :

cannot clean the air.

 results in poor cooling.

 may cause odour.

Cleaning the air filters

(It is recommended to clean  them every 

two 

weeks.)

Push

l

Insert claws of the filters into slots of the front panel. The
front grille should lock at both sides and at the point in
the middle. Push the grille at the 3 points indicated by   .

Open the front grille and pull out the
air filters.

Take off the air
purifying filters.

1

2

l

Wipe them with dry soft cloth.
For cleaning, do not use water hotter than 40˚ C, benzine,
gasoline, thinner, nor other volatile oils, polishing compound,
scrubbing brushes nor other hard stuff.

Replacing air purifying filters

(It is recommended  to  replace  them  every  three
months.)

l

Air purifying filters need to be replaced regularly.

Detach the filter
element and
attach a new
one .

3

Attach the air
purifying filter .

4

Set the air
filters as they
were and close
the front grille

.

(Push the grille at the 3
points, two at both
sides and in the
middle.)

5

Item

Part No.

Air purifying filter (with frame)

KAF918A41

Air purifying filter (without frame)

KAF918A42

15

Check

Check that the base, stand and other
fittings of the outdoor unit are not decayed
or corroded.

Check that nothing blocks the air inlets and
the outlets of the indoor unit and the
outdoor unit.

Check that the earth wire is not
disconnected or broken.

Check that the drain comes smoothly out
of the drain hose during COOL or DRY
operation.

l

If no drain water is seen, water may be leaking from the
indoor unit. Stop operation and consult the service shop if
this is the case.

Before a  long  idle  period

2

Clean the air filters and set them again.

3

Take out batteries from the remote
controller.

4

Turn OFF the breaker for the room air
conditioner.

1
2

Press 

MODE

 and select "

 

 ".

Press 

ON/OFF

 .

Perform this operation when the room
temperature is under 28˚C.

Care and Cleaning

<FTK>

1

Operate the fan alone for several hours
on a fine day to dry out the inside.

<FTX>

1

3

2

Press 

ON/OFF

 .

Press 

MODE

 and select "

 

 ".

Press 

TEMP

 and set the temperature to 32˚C

Cleaning the front grille

 CAUTION

You may  remove the front grille  for cleaning.

Open the front grille .

l

Hold the grille by the tabs on the two sides and lift it until
it stops with a click.

1

3

Clean the front  grille.

l

You may wipe it with a soft cloth soaked in water.

l

Only neutral detergent may be used.

l

You may wash the grille with water. After washing, dry it
with cloth, then dry it up in the shade.

2

Remove the front grille.

l

Supporting the front grille with one hand, release the lock
by sliding down the knob with the other hand.

l

To remove the front grille, pull it toward yourself with both
hands.

4

Attach the front grille .

l

Set the 3 keys of the front grille into the slots and push
them in all the way.

l

Supporting the front grille with one hand, fit the lock by
sliding up the knob with the other hand.

l

Close the front grille slowly in this state. (Push the grille
at the 3 points, two at both sides and in the middle.)

l

When removing or attaching the front grille, use a robust
and stable stool and watch your steps carefully.

l

When removing or attaching the front grille, support the
grille securely with hand to prevent it from falling.

l

For cleaning, do not use water hotter than 40˚C, benzine,
gasoline, thinner, nor other volatile oils, polishing compound,
scrubbing brushes nor othe hard stuff.

l

After cleaning, make sure that the front grille is securely fixed.

Fit the key

into the slot.

Slide up the knob.

2P042644-1C

Summary of Contents for FTX-J Series









Reviews: