ED12-011A
Operation Manual
Room Air Conditioners SUPER MULTI H-Series
97
10
In DRY mode or COOL mode
In HEAT or FAN mode
When stop operation
Upper limit in cooling
Lower limit in cooling
0˚
25˚
20˚
45˚
When stop operation
Upper limit in heating
Lower limit in heating
.......
To stop the flap at an
angle you like, press
SWING
.
Adjusting the
horizontal blade (flap)
You can adjust the air flow direction to increase your
comfort.
l
Be careful when adjusting the louvre. Inside the air
outlet, a fan is rotating at a high speed.
ATTENTION
Notes on flap angles
l
When
SWING
is selected, the flap swinging range depends
on the operation mode. (See the figure.)
l
The real flap angles are differ from the display of remote
controller.
Press
SWING
.
l
Every time the button is pressed, "
" appears or disappears.
.......
The flap automatically
swings up and down.
Adjusting the Air Flow Direction
l
Always use a remote controller to adjust the flap angle. If
you attempt to move it forcibly with hand when it is
swinging, the mechanism may be broken.
ATTENTION
Adjusting the louvre
Hold the knob and move the louvre.
(You will find a knob on the left-side and the right-side
blades.)
ON
ON
11
Notes on OFF TIMER
l
NIGHT SET MODE
When the OFF TIMER is set, the air conditioner automatically
adjusts the temperature setting (0.5ºC up in COOL, 2.0˚C down
in HEAT) to prevent excessive cooling (heating) for your
pleasant sleep.
Timer functions are useful for automatically switching the
air conditioner on or off at night or in the morning. You can
also use OFF TIMER and ON TIMER in combination.
1
Press
OFF
while the air conditioner
is operating.
l
Chec k that the clock is correct.
If not, set the clock to the present time. (See page 7.)
Press
CANCEL
.
Then the TIMER lamp lights up.
n
To cancel the timer:
Press
OFF
once again.
Then the TIMER lamp goes off.
OFF TIMER operation
Press
TIMER
until the time setting
reaches the point you like.
l
Every pressing of either button increases or decreases
the time setting by 10 minutes. Holding down either
button changes the setting rapidly.
2
3
Press
ON
while the air conditioner is
not operating.
Press
ON
once again.
Press
TIMER
until the time setting
reaches the point you like.
l
Every pressing of either button increases or decreases
the time setting by 10 minutes. Holding down either
button changes the setting rapidly.
ON TIMER operation
1
2
3
Combining ON TIMER and OFF TIMER
l
A sample setting for combining the two timers is shown below.
Press
CANCEL
.
n
To cancel the timer:
Then the TIMER lamp goes off.
Then the TIMER lamp lights up.
l
Check that the clock is correct. If not, set the clock to the present
time (See page 7).
Timer Operation
AM
is displayed.
blinks.
* Previous time setting
appears on display.
AM
is displayed.
blinks.
* Previous time setting
appears on display.
AM
Displa
y
AM
Displa
y
Displa
y
AM
Present time: 11:00 PM
(The unit operating)
OFF TIMER at 0:00 a.m.
ON TIMER at 7:00 a.m.
Combined
(Example)
Notes on ON,OFF TIMER
l
When TIMER is set, the present time is not displayed.
l
Once you set ON,OFF TIMER, the time setting is kept in the
memory. (The memory is canceled when remote controller
batteries are replaced.)
ATTENTION
AM
Displa
y
ON
OFF
AM
AM
Displa
y
n
In the following cases, set the timer again.
l
After a breaker has turned OFF.
l
After a power failure.
l
After replacing batteries in the remote controller.
ON
OFF
12
•
The "Good Sleep Cooling Operation" makes the 1/f Fluctuating Temperature.
It brings you comfortable sleep as it prevents from getting chilied.
Press
-SLEEP
in cooling operation.
n
To change the temperature setting.
(See page 8.)
n
To change the air flow rate setting.
(See page 8.)
n
To change the air flow direction setting.
(See page 10.)
n
To cancel the "Good Sleep Cooling Operation ", press
-SLEEP
.
→
Back to the normal cooling opration.
1
Good Sleep Cooling Operation
(G-SLEEP)
Notes on "Good sleep cooling operation "
l
We adopt the 1/f fluctuation rhythm in temperature control.
A 1/f fluctuation rhythm is used in temperature control. With it, temperature is fluctuated within a ±1˚C
range of the set temperature.
The 1/f fluctuation is comfortable rhythm existed in the natural world. (refer to "What's the 1/f
fluctuation")
l
Air blow is the lowest when the fan is set to "AUTO".
l
If you don't like this function, change the operation mode. (See page 8)
What is 1/f fluctuation...
It seems irregular but there seems to be a self-resemblance rule in our mother nature.
For example, the waves in the ocean forms irregularly but when you look at the coast line, there are
some places where they look similar.
When you look close around you, our heart doesn't beat in regular intervals but shows "1/f
fluctuation" in a long term. The research shows this "1/f fluctuation" and comfort has some kind of
relation and is applied to the comfort control fiels.
13
Press
SENSOR
While the air conditioner
is operating. (The Sensor lamp lights up.)
n
To cancel the "Intelligent Eye",
press
SENSOR
. (The Sensor lamp goes off.)
[EX.]
1
Intelligent Eye
n
Adjusting the angle of the
Intelligent-eye sensor
•
You can adjust the angle of the Intelligent-eye
sensor to remove the detection area.
(Adjustable angle: 15˚ to right and left of
centre)
•
Gently push and slide the sensor to adjust
the angle.
•
After adjusting the angle, gently wipe the
sensor with a clean cloth, being careful not to
scratch the sensor.
CAUTION
•
Do not hit or violently push the Intelligent-eye sensor. This
can lead to damage and malfunction.
"Intelligent Eye" is the infrared sensor which detecs the
human movement.
Intelligent-eye
sensor
15˚
15˚
Moving the sensor to the left
Moving the sensor to the right
When somebody in the room
•
Normal operation
(The sensor lamp lights up.)
When nobody in the room
•
20 min. after, start save operation.*
(The sensor lamp goes off.)
Sombody back in the room
•
Back to normal operation.
(The sensor lamp lights up again.)
"Intelligent Eye" is useful for
Energy Saving
* Save operation
l
Change the temperature –2˚C in heat/ +2˚C in cool/ +1˚C in
dry mode from set temperature.
l
Decrease the air flow rate slightly in fan operation.
Notes on "Intelligent Eye"
l
Saving operation will not go on during
powerful operation.
l
Night set mode (see page 11.) will not go on
during you use Intelligent Eye.
l
You can sleep more comfortablly by using
"Good Sleep Cooling Operation (G-SLEEP)"
function (see page 12.) at the same time.
Do not place large objects near the sensor.
Also keep heating units or humidifiers outside
the sensor's detection area.
This sensor can detect objects it shouldn't as
well as not detect objects it should.
CAUTION
l
Application range is as follows.
l
Sensor may not respond when you are 5m or
more away. (Check the application range)
l
Sensor detection sensitivity changes according
to indoor unit location, the speed of passersby,
temperature range, etc.
l
The sensor also mistakenly detects pets,
sunlight, fluttering curtains and light reflected
off of mirrors as passersby.
80˚
50˚
5m
50˚
5m
Vertical angle 40˚
(Side View)
Horizontal angle 50˚
(Top View)
