Daikin FT25GV1G6 Service Manual Download Page 5 | Manualshive

Page: 5 / 34

background image

Si041048

Removal of Air Filters

Removal Procedure

3

3. Remove the Titanium

apatite photocatalytic air-
purifying filters.

Some models have no
Titanium apatite
photocatalytic air-purifying
filter.

The right and left filters are
interchangeable.

1

The Titanium apatite
photocatalytic air-
purifying filter ASSY is
attached to the back of
the air filter.

2

3

Remove the Titanium
apatite photocatalytic
air-purifying filter ASSY
by bending the air filter
and releasing the
projections from the air
filter frame.

Remove the Titanium
apatite photocatalytic
air-purifying filter from
its frame (at 5 positions)
by bending it.

Step

Procedure

Points

Air filter

(R4309)

Titanium apatite
photocatalytic
air-purifying filter
ASSY

Projection

(R16029)

(R13174)

«
...
3
4
5
6
7
...
»

Summary of Contents for FT25GV1G6



































Reviews:

No comments

Related manuals for FT25GV1G6

Brand: ValuTek Pages: 4

Brand: ebm-papst Pages: 10

Brand: ebm-papst Pages: 12

Brand: NOMA Pages: 13

Brand: ebm-papst Pages: 10

Brand: Paris Rhone Pages: 21

Brand: Fanaway Pages: 36

Brand: ebm-papst Pages: 13

Brand: Parrot Uncle Pages: 10

Brand: Maico Pages: 4

Brand: Lindab Pages: 25

Brand: lauson Pages: 14

Brand: Hunter Pages: 26

Brand: ebm-papst Pages: 5

Brand: Vortice Pages: 20

Brand: FlaktWoods Pages: 16

Brand: Canarm Pages: 2

KLOUT FP3070 Series

Brand: Fanimation Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands