background image

21

English

In case the piping penetration cover is cut off and used as wiring penetration hole, after the wiring connec-
tion is finished, mend the cover.

Seal the clearance around the wirings with putty and insulating material (field supply).
(If insects and small animals get into the indoor unit, short circuiting may occur inside the control box.)

If the low voltage wiring (remote controller wiring) and the high voltage wiring (transmission wiring, earth 
wiring) are brought into the indoor unit from the same place, they may be affected by electric noise (outside 
noise) and cause malfunction or failure.

Keep the distance of 50mm or more between the low voltage wiring (remote controller wiring) and the high 
voltage wiring (transmission wiring, earth wiring) at anywhere outside the indoor unit. If both the wirings are 
laid down together, they may be affected by electric noise (outside noise) and cause malfunction or failure.

9-2 WIRING EXAMPLE

CAUTION

Be sure to install an earth leakage breaker to the outdoor unit.
This is to avoid electric shocks or a fire.

For the wiring of outdoor units, refer to the installation manual attached to the outdoor units. Confirm the sys-
tem type.

• Pair  type

: 1 remote controller controls 1 indoor unit (standard system). 

(Refer to Fig. 31)

• Simultaneous operation system

: 1 remote controller controls 2 indoor units

(2 indoor units operates equally). 

(Refer to Fig. 32)

• Group control

: 1 remote controller controls up to 16 indoor units

(All indoor units operate according to the remote controller). 

(Refer to Fig. 33)

Remote controller wiring

(1) Install the fixture at the wiring 

entrance side.

Power supply wiring 
and Earth wiring

DETAIL

Wiring fixture (11) (accessory)

Clamp (4) (accessory)

Clamp (4) (accessory)

(3) To avoid the loosing of the power supply wiring 

and Earth wiring, band the clamp to tightly fit the 
fixture at terminal block side.

(2) Fix the wiring to the fixture by clamps so that  no 

tension will be given to the terminal connection.

Putty or insulation
(field supply)

Refrigerant piping

Remote controller wiring

Low voltage wiring

Drain piping

Distance of 50mm between

High voltage wiring

Resin bushing (10)
(accessory)

Transmission 
wiring and 
Earth wiring

01_EN_3P249378-6L.fm  Page 21  Sunday, September 30, 2012  2:30 PM

Summary of Contents for FHQ35CAVEB





































Reviews: