Daikin FC2 Installation, Use And Maintenance Manual Download

Page: 12 / 56

Translation from original instructions

Packaged Rooftop

We reserve the right to make changes without any prior notice.

UATYA

4P645202-1

2.2.1 Limits to the use – Minimum area of the conditioned space and maximum

refrigerant charge

Clause GG.9 of Annex GG within the standard IEC 60335-2-40:2018 (Household and similar electrical appliances -

Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers) defines the

charge limits based on the total conditioned space area and the ventilation requirements for ducted appliances using

A2L refrigerants. For full details refer to the standard IEC 60335-2-40:2018.
The minimum total conditioned room area "TA

min

" of installed appliance with refrigerant charge "m

" (kg) shall be in

accordance with following:

Unit

For units without hot gas post heating coil

For units with hot gas post heating coil

min

[kg]

Circuit 1

Circuit 2

Circuit 1

Circuit 2

UATYA25

20,7

8,3

24,4

UATYA30

29,6

11,3

33,5

UATYA40

35,5

13,7

40,6

UATYA50

44,4

50,4

UATYA60

53,3

UATYA70

53,3

UATYA80

68,1

26,9

79,6

UATYA90

71,1

UATYA100

82,9

32,3

95,7

UATYA110

88,8

34,7

102,8

UATYA120

106,6

41,2

122,1

UATYA140

56,3

23,1

68,4

UATYA150

56,3

23,1

68,4

UATYA160

68,1

27,9

82,6

UATYA180

UATYA190

No zoning dampers shall be installed in the rooms considered to determine the minimum room area

unless these zoning dampers can be fully opened by the control signal of the rooftop in case of a leak

If the refrigerant charge is adjusted on the field, the minimum area must be re-evaluated in order to be always above

the result obtained through the following formula:

where

- m

added

is the refrigerant charge added on the field in kg.

The sum “m

added

" must be lower than 79,8 kg for each circuit.

The minimum area according to the area of the conditioned space is shown below

[m²]

100

150

200

250

[kg]

Fig. 1 Total min. installation area

Summary of Contents for FC2
























































Search results

Summary of Contents for FC2

Reviews:

Related manuals for FC2

Brands by name

Popular brands

Daikin FC2, Installation, Use And Maintenance Manual

Search results

Summary of Contents for FC2

Reviews:

Related manuals for FC2

Brands by name

Popular brands