background image

11

English

Indoor Unit Installation

1) Replace the drain plug and drain hose. 

(How to replace the drain plug and drain hose.)

2) Pull in the refrigerant piping and lay it so that it matches the liquid and gas piping marked on the 

 mounting plate.

3) Hook the indoor unit onto the 

 mounting plate. 

4) Connect the pipes. If it is difficult to do, remove the front grille first.

5) Wrap the insulation on the 

piping with insulation tape. If 
you are not replacing the drain 
hose, store it in the location 
shown as right figure. 

6) While exercising care so that the inter-unit wiring do not catch indoor 

unit, press the bottom edge of indoor unit with both hands until it is 
firmly caught by the mounting plate hooks.  Secure indoor unit to the 
mounting plate with screws (M4 × 12L). 

5-3. Wall embedded piping. 

Follow the instructions given under  

1) Insert the drain hose to this depth so it won’t be pulled out of the drain 

pipe.

Left-side, left-back, or left-bottom piping

 .

• Left-back piping

• Left-bottom piping

• Left-side piping

Cut out the 
piping-through hole.

Refrigerant pipe

Drain hose

Humidifying hose

Refrigerant pipe

Cut out the 
piping-through hole.

Humidifying hose

Refrigerant pipe

A

A

Drain hose

Bind with 
plastic tape.

 A Mounting plate

Wrap insulating tape around the bent portion 
of refrigerant pipe. 
Overlap at least half the width of the tape 
with each turn.

Caulk this hole 
with putty or 
caulking material.

Refrigerant
pipes

Bottom frame

H  M4 × 12L (2 point)

Mounting
plate

A

Drain hose

Inter-unit wiring

Inner wall

Vinyl chloride 
drain pipe 
(VP-30)

Drain hose

50mm 
or more

Insert the drain hose 
to this depth so it 
won’t be pulled out 
of drain pipe.

Outer wall

01_EN_3P232706-1A.fm  Page 11  Friday, November 21, 2008  4:19 PM

Summary of Contents for CTXU25G2V1B


















Reviews: