background image

4 Installation

Installation manual

5

EBLQ+07CAV3
Daikin Altherma low temperature monobloc
4P403578-1F – 2018.06

3.3

Preparing electrical wiring

3.3.1

Overview of electrical connections for
external and internal actuators

Item

Description

Wires

Maximum

running

current

Outdoor unit power supply

1

Power supply for
outdoor unit

2+GND

(a)

2

Normal kWh rate power
supply

2

6.3 A

User interface

3

User interface

2

(b)

Optional equipment

4

Remote outdoor sensor 2

(c)

Field-supplied components

5

Domestic hot water
pump

2

(c)

6

Space heating/cooling
operation control (or
shut‑off valve)

2

(e)

Interconnection cable

7

Interconnection cable
between outdoor unit
and control box

2

(d)

(a)

Refer to name plate on outdoor unit.

(b)

Cable section 0.75 mm² till 1.25 mm²; maximum length:
500 m. Applicable for both single user interface and dual
user interface connection.

(c)

Minimum cable section 0.75 mm².

(d)

Cable section 0.75 mm² till 1.25 mm²; maximum length:
20 m.

(e)

If valve kit EKMBHBP1 is part of the system, then the
required cable section is 0.75 mm². If valve kit EKMBHBP1
is NOT part of the system, then the minimum required
cable section is 0.75 mm².

NOTICE

More  technical  specifications  of  the  different  connections
are indicated on the inside of the outdoor unit.

4

Installation

4.1

Opening the units

4.1.1

To open the outdoor unit

DANGER: RISK OF ELECTROCUTION

DANGER: RISK OF BURNING

1

2

4.1.2

To open the switch box cover of the
indoor unit

4.2

Mounting the outdoor unit

4.2.1

To provide the installation structure

INFORMATION

For  information  on  the  available  options,  contact  your
dealer.

If  the  unit  is  installed  directly  on  the  floor,  prepare  4  sets  of  M8  or
M10 anchor bolts, nuts and washers (field supply) as follows:

INFORMATION

The  maximum  height  of  the  upper  protruding  part  of  the
bolts is 15 mm.

Summary of Contents for Altherma EBLQ05CAV3





























Reviews: