background image

General

Proper installation of the ExtendAire conditioner described 
herein requires strict adherence to these installation  
instructions.

Description

The ExtendAire conditioner is a cabinet extension kit designed 
to provide balanced heating and cooling in two rooms using a 
single Incremental conditioner. Components of the ExtendAire 
are shown in 

Figure 1

 and listed in 

Table 1

.

Unpacking

Open the carton and check the contents. Report missing or 
damaged parts to the carrier immediately.

 

!

CAUTION

  Sharp metal edges are a hazard, use care when servicing to 

avoid contact with them.

Applied PTAC ExtendAire™ for Models PDAE/PDHE 
& PDAF/PDHF & Optional Boost Fan Installation

For Adjoining Room Applications

 

Installation & Maintenance Data   

 

IM 871-3

 

  

 

Group: 

Applied PTAC/HP

 

 

  

 

Part Number: 

910116725

 

  

 

Date: 

October 2011

Figure 1: ExtendAire Component Descriptions

1.  End Cap

2.  3' Extension Section

3.  Shelf Discharge Section

4.  Primary Discharge Section

5.  Trim Piece

Table 1: ExtendAire Duct Extension Option

 

Description  

Quantity in

 

 

Each Package 

Part Number

  Primary Discharge Section

1

 

 910106134

  Shelf Discharge Assembly - Primary Discharge Section

1

 1

  Shelf Discharge Assembly - 3-Foot Extension Section 

1

  Shelf Discharge Assembly - Shelf Discharge Section 

 

910106137

  Shelf Discharge Assembly - Trim Piece 

2

  Shelf Discharge Assembly - End Cap 

2

  Side Wall Outlet Assembly

2

 - Primary Discharge Section

1 1

 

Side Wall Outlet Assembly

2

 - 3-Foot Extension Section 

 

910106138

  Side Wall Outlet Assembly

2

 - Trim Piece 

1

  Side Wall Outlet Assembly

2

 - End Cap 

1

Notes: 

1

  Control door and end cap are included in Primary Discharge Section.

 

2

  Discharge grille in adjoining room to be supplied by others. Additional 3-foot extension sections must be ordered in    

 

packages as shown in 

Table 2

.

Table 2: Supplementary Accessories

 

Description  

Quantity in

 

 

Each Package 

Part Number

  3-Foot Extension Section Pack - 3-Foot Extension 

 

061389601

  3-Foot Extension Section Pack - Trim Piece 

2

NOTICE

  When a 3 foot (or greater) extension section is added to the pri-

mary discharge section, the (optional) boost fan is recommend-
ed. The Boost Fan operates when the indoor fan operates, to 

assist unit airflow into the adjoining room.

©2013 Daikin Applied   •   www.DaikinAP.com   •   (800) 432-1342

Summary of Contents for 910116725













Reviews: