Daikin 2MXS52E2V1B Installation Manual Download Page 13 | Manualshive

Page: 13 / 19

Daikin 2MXS52E2V1B Installation Manual Download Page 13

11

■

English

Pump Down Operation

In order to protect the environment, be sure to pump down when relocating or disposing of the unit.

1) Remove the valve lid from liquid shut-off valve and gas shut-

off valve.

2) Carry out forced cooling operation.
3) After five to ten minutes, close the liquid shut-off valve with a

hexagonal wrench.

4) After two to three minutes, close the gas shut-off valve and

stop forced cooling operation.

1.

Forced operation

1) Turn the Operation Mode switch (SW2) to “COOL”. (Heat pump only)
2) Press the Forced Operation switch (SW1) to begin forced cooling. Press the Forced Operation switch (SW1) again to stop

forced cooling.

Gas shut-off valve

Close

Hexagonal
wrench

Liquid shut-off
valve

Valve lid

Service PC-board

Operation Mode
switch (SW2)

Forced Operation
switch (SW1)

01_EN_3P164392-2E.fm Page 11 Wednesday, May 24, 2006 2:47 PM

«
...
11
12
13
14
15
...
»

Summary of Contents for 2MXS52E2V1B




















Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands