Dahua Mobile DVR Series Page 29 User Manual Download

Page: 29 / 172

Figure 3-6

3.3.2

SIM Card/SD Card Installation

This series product supports built-in SIM card/SD card. See Figure 3-7.

Step 1 Remove the HDD box.

Step 2 Insert the SIM card and the SD card to the corresponding slot.

Figure 3-7

Step 3 Install HDD box.

3.4 Alarm Input and Output Connection

There are two alarm input types for you to select: normal open (NO) and normal close (NC).

1. Alarm input

a. Alarm input supports grounding alarm input.

c. When the alarm device is connecting one DVR and one other device, please use a relay to

separate them,

2. Alarm output

The alarm output max load shall be less than 0.5A. It should not be connected to high power load

directly to avoid high current which may result in relay damage. Please use t he co contactor to

realize the connection between the alarm output port and the load.

Summary of Contents for Mobile DVR Series













































































































































































Search results

Summary of Contents for Mobile DVR Series

Reviews:

Related manuals for Mobile DVR Series

Brands by name

Popular brands

Dahua Mobile DVR Series, User Manual

Search results

Summary of Contents for Mobile DVR Series

Reviews:

Related manuals for Mobile DVR Series

Brands by name

Popular brands