background image

                                                                           

 

 

2  Device Installation  

2.1  Lens Installation 

 

Figure 2-1 

 

2.1.1  Auto Iris Lens Installation  

Step 1  

Remove the CCD protection cover on the device, aim the lens at the lens installation position, 

and turn the lens clockwise until it is installed firmly.  

Step 2  

Insert the lens cable plug into the connector of auto iris lens on the camera side panel.  

Step 3  

Make the image clear via adjusting focal length.  

 

2.1.2   Manual Iris Lens Installation  

Please follow the steps listed below for auto aperture lens installation.  

Step 1  

Remove the CCD protection cover of the device, 

Step 2  

Install the C/CS adapter ring on the camera; turn clockwise to the end to cling to the focusing ring 

on the camera closely. (Only C lens needs to install adapter ring) 

Step 3  

 Aim the C port lens at the lens installation position of the C/CS adapter ring (aim the CS port 

lens at the lens installation position of the camera focusing ring); turn the lens clockwise until it is 

firmly installed.  

Step 4  

Use slotted screwdriver to unfasten the screw near the focusing ring and then turn counter 

clockwise to move the focusing ring out for several millimeters.  Now you can focus manually and 

check t

he video is clear or not. If you can’t see the clear video, you can adjust back focus. 

Step 5  

After you completed the focus setup, use the slotted screwdriver to fix the screw firmly. Fasten 

the focusing ring. Now the installation completed.  

Summary of Contents for H-IPC-HF81230E


















Reviews: