Dahua DH-SD6C430U-HNI Installation Manual Download Page 29

Page: 29 / 29

APPENDIX Ⅲ SAFETY ROPE INSTALLATION

Remove one M4 screw from the speed dome and then use the M4 screw of the safety rope to fix

the safety rope on the speed dome.

Please note the contents in this chapter are for hang (pendant) mount installation only.

Note



This manual is for reference only. Slight difference may be found in the user

interface.



All the designs and software here are subject to change without prior written

notice.



All trademarks and registered trademarks are the properties of their respective

owners.



If there is any uncertainty or controversy, please refer to the final explanation of us.



Please visit our website or contact your local service engineer for more

information.

Speed Dome M4 Screw

Safety Rope

M4 Screw of the

Safety Rope

Speed Dome

Summary of Contents for DH-SD6C430U-HNI






























Search results

Summary of Contents for DH-SD6C430U-HNI

Reviews:

Related manuals for DH-SD6C430U-HNI

Brands by name

Popular brands

Dahua DH-SD6C430U-HNI, Installation Manual

Search results

Summary of Contents for DH-SD6C430U-HNI

Reviews:

Related manuals for DH-SD6C430U-HNI

Brands by name

Popular brands