Dahua DH-SD60230U-HNI Installation Manual Download Page 9

Page: 9 / 44

INTELLIGENT SPEED DOME INSTALLATION

1.1

Installation Preparation

Basic Requirement



All installation and operation here should conform to your local electrical safety codes.



Before installation, please open the package and check all the components are included.

Please make sure the speed dome installation environment and installation mode can meet

your requirement. If there is special requirement, please contact your local retailer for more

information.



We assume no liability or responsibility for all the fires or electrical shock caused by

improper handling or installation.

Check installation space and installation location intension

Please make sure the installation environment has enough space to install the speed dome and

its corresponding bracket.

Please make sure the ceiling, wall and the bracket can support the speed dome and its

corresponding installation component. It shall sustain the 8X weight of the speed dome. Please

notice that the installation height should be more than 6m if it is a laser speed dome.

About cable

Please select the cable according to your transmission distance.

The minimum video coaxial-cable requirement is:



75 ohm.



Full cable with copper conductor



95% knitted copper shield



Please refer to appendix 2 for more information about RS485 communication cable.

International Model

Max Distance
(Ft\M)

RG59/U

750ft (229m)

RG6/U

1,000ft (305m)

RG11/U

1,500ft (457m)

Note:

The above can be applied to analog SD and network SD.

International Model

Max Distance
(Ft\M)

SYV-75-3

720P

（

25fps\30fps)

：

500M/1640ft

720P

（

50fps\60fps)

：

300M/984ft

1080P

（

25fps\30fps)

：

300M/984ft

Note:

The above can be applied to HDCVI SD.

Select proper power supply cable according to transmission distance

Summary of Contents for DH-SD60230U-HNI













































Search results

Summary of Contents for DH-SD60230U-HNI

Reviews:

Related manuals for DH-SD60230U-HNI

Brands by name

Popular brands

Dahua DH-SD60230U-HNI, Installation Manual

Search results

Summary of Contents for DH-SD60230U-HNI

Reviews:

Related manuals for DH-SD60230U-HNI

Brands by name

Popular brands