Dahua DH-DVR0404ME-HE User Manual Download

Page: 13 / 144

Playback

Mode

Various fast play, slow play speeds, manual frame by frame playback and

reverse play mode.

Various File

Switch

Ways

Can switch to previous or next file or any file in current play list.

Can switch to file on other channel of the same time. (If there is a file)

Support file continuous play, when a file is end system auto plays the next

file in the current channel

Multi-chann

el Playback

There is 1/4channel playback mode.

Window

Zoom

Switch between self-adaptive screen/full screen when playback

Partial

Enlargemen

When in one-window full-screen playback mode, you can select any zone

to activate partial enlargement function.

Backup

function

Backup

Mode

HDD backup

Support peripheral USB backup device. (Flash drive)

Support network download and save

Network

Function

Network

control

View monitor channel remotely.

DVR configuration through client-end and web browser

Upgrade via client or browser to realize remote maintenance.

View alarm information such as external alarm, motion detection and

video loss via client.

File download backup and playback

Multiple devices share information via corresponding software such as

professional surveillance software (PSS)

Duplex transparent COM

Network alarm input and output

Bidirectional audio.

Motion

Detection and

Alarm

Motion

Detection

Zone setup: support 396((PAL 22×18, NTSC 22×15)) detection zones.

Various sensitivity levels.

Alarm can activate record or external alarm or screen message prompt.

Video Loss Alarm can activate external alarm or screen message prompt.

External

Alarm

Support record activation function or activate external alarm or screen

message in specified period.

Manual

Alarm

Control

Enable or disable alarm input channel

Support analog alarm signal to specific alarm output channel.

Alarm Input

7-ch alarm input

（

You can set normal open or normal close type to select

the alarm type.

）

Alarm

Output

2-channel relay output.

Interface

USB

Interface

2 USB 2.0 ports.

One is at the front panel and the other is at the extension cable of the rear

panel.

Network

connection

RJ45 10M/100M/1000M self-adaptable Ethernet port

Summary of Contents for DH-DVR0404ME-HE

















































































































































Search results

Summary of Contents for DH-DVR0404ME-HE

Reviews:

Related manuals for DH-DVR0404ME-HE

Brands by name

Popular brands

Dahua DH-DVR0404ME-HE, User Manual

Search results

Summary of Contents for DH-DVR0404ME-HE

Reviews:

Related manuals for DH-DVR0404ME-HE

Brands by name

Popular brands