background image

1. Connect  the  m ain lead  to an electrical  outlet.

2.  After placing the  food in  a suitable  container, open the  oven door  and  put it on the  glass  tray. The glass tray  m ust  always

be in place during cooking. 

3. Close the door securely.

4. W hen the oven  door  is  opened, the light  turns off.

5. The oven door can  be opened at  any tim e during operation  by touching  the door release button  on the  control  panel. 

The  oven will autom atically shut  off. To restart the oven,  close the door and  then  touch START.

6. Each  tim e  a  pad is touched,  a BEEP  will sound  to acknowledge the touch.

7. The oven autom atically cook on full power unless set to  a  lower power level.

8. The display will  show :0 when  the oven is plugged  in.

9. Tim e  clock returns to the present  tim e  when the cooking tim e ends.

10. W hen the STO P /CLEAR  pad is touched during the oven operation, the oven stops cooking and all inform ation retained.

To erase all  inform ation (except the present tim e), touch the STO P/CLEAR pad  once  m ore. If  the  oven door is opened

during the oven operation, all inform ation is retained.

11. If the START  pad  is  touched and the oven does not operate,  check the area betw een  the  door and  door is closed

securely. The oven will not start cooking under the door is com pletely closed or the program  has been reset. 

W attage output chart

The power level is set by pressing the Power pad. The chart shows the display, the power level and the percentage of 

power.

Touch Power pad.

Pow er level (Display)

Approxim ate Percentage of Pow er

O nce

P -H I

100 %

Tw ice

P -90

90 %

3 tim es

P -80

80 %

4 tim es

P -70

70 %

5 tim es

P -60

60 %

6 tim es

P -50

50 %

7 tim es

P -40

40 %

8 tim es

P -30

30 %

9 tim es

P -20

20 %

10 tim es

P -10

10 %

11 tim es

P -00

0 %

OPERATIONS AND FUNCTIONS

M ake sure the oven is properly installed and plugged into the electrical outlet.

Summary of Contents for KOR-63BG0S






































Reviews: