manualshive.com logo in svg

Daewoo KOR-63350S, Service Manual, Page: 9 / 26

Share
Download
Daewoo KOR-63350S Service Manual Download Page 9

8

DISASSEMBLY AND ASSEMBLY

1. To remove cabinet

     1) Remove three screws on cabinet back.
     2) Push the cabinet backward.

2. To remove door assembly

    1) Remove screws which secure the stopper hinge top.
    2) Remove the door assembly from top plate of cavity.
    3) Reverse the above for reassembly.

3. To remove door parts.

(1) KOR-63350S

REF NO.

PART CODE

PART NAME

DESCRIPTION

Q’TY

REMARK

A01

3512203860

FRAME DOOR

ABS SG-175

1

A02

3517005630

BARRIER-SCREEN*O

SAN

1

A03

3515204100

STOPPER HINGE*T AS

KOR-63150S

1

A04

3511705500

DOOR WELD AS

KOR-61150S

1

A05

3517002800

BARRIER-SCREEN*I

POLYESTER T0.1

1

A06

3512300200

GASKET DOOR

PP

1

A07

3513100700

HOOK

POM

1

A08

3515101300

SPRING HOOK

PW1

1

A06

A05

A04

A02

A01

A03

A07

A08

   After replacing the door assembly, perform a check of correct alignment with the hinge and cavity front plate.

NOTE

✔ 

Caution:

In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the

latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr)

Summary of Contents for KOR-63350S



























Reviews:

No comments