background image

9

The pizza tray can be opened at any time during operation by pulling out the handle on the pizza tray. The pizza oven will
automatically shut off.

Touch the pizza menu pad and the symbol of menu will be displayed.

Each time a pad is touched, a BEEP sounds to acknowledge the touch.

Enter the cooking time and touch pizza start pad and then the pizza indicator linghts and the  cooking time is displayed
and then pizza cooking starts. During the pizza cooking, hot smoke or air may goes out from the gap of the pizza tray.

When the pizza PAUSE/CANCEL pad is touched during the oven operation, the pizza stops cooking and all information
retained. To erase all information(except the present time), touch the  PAUSE/CANCEL pad once more. If the pizza tray
is opened during the pizza operation, all information is retained.

If the pizza START pad is touched and the pizza does not operate, check the pizza tray is closed securely. The pizza
oven will not start cooking until the pizza tray is completely closed or the program has been reset.

Before using the pizza oven for the first time, operate the pizza oven without pizza for about 5 minutes in order to burn
off residues on the heating elements. You will notice an odor that is characteristics of new heating elements. This is
normal and will soon disappear. 

Always unplug the Pizza baker built-in microwaves combo and allow the pizza oven to cool completely before cleaning.

Pizza Tray: 
Wipe surface with a soft, clean, damp cloth. Never use abrasive cleaners, as they may scratch the surface. Do not use
fork or other sharp, metal object to clean the pizza tray, or to remove pizza, as it may damage the pizza tray.

This section includes useful information about pizza oven operation.

1. Plug power supply cord into a standard 3-pronged 15Amp, 230V AC 50Hz power output.
2. Put pizza on the pizza tray.
3. Shut the pizza tray. Make sure that it is firmly closed.

1

2
3
4

5

6

NOTE :
When the pizza tray is opened after pizza cooking, hot smoke or air will go out and the pizza tray is very hot. 
Take out food carefully not to touch hot surfaces of the pizza oven or pizza tray or hot air.

When the microwave oven is working, touching pizza PAUSE/CANCEL pad can’t stop MWO cooking.

NOTE :
When the pizza oven is operated several times in series and is overheated, the safety thermal switch works and
the heating elements stop operating. So, though the pizza oven seems to operate normally, it does not cook pizza. 
Open the pizza tray and cool it for 4~5 min. 
After then the pizza can cook normally.

OPERATION PROCEDURE(PIZZA OVEN)

IMPORTANT

CLEANING THE PIZZA OVEN

Summary of Contents for KOD-135P9S






































Reviews: