Daewoo KOC-970T1S Service Manual Download Page 17 | Manualshive

Page: 17 / 48

background image

DISASSEMBLY AND ASSEMBLY

10. To remove motor syncro and under heater

(1) Cut the syncro motor cover parts from the base plate.

(2) Remove two screws which secure the motor syncro and supporter to bracket syncro motor.

(3) Remove two screws and under heater assembly in cavity

11. To remove grill heater assembly

(1)

Remove two screws which secure the cover insulator *t to top plate.

(2) Remove the harness between heaters.

(3) Remove two screws for removing heater brackets.

(4) Remove heaters.

(5) Reverse the above steps for reassembly.

«
...
15
16
17
18
19
...
»

Summary of Contents for KOC-970T1S

















































Reviews:

No comments

Related manuals for KOC-970T1S

Brand: Hyundai Pages: 26

Brand: Daewoo Pages: 36

Brand: Galanz Pages: 13

Brand: DAEWOO ELECTRONICS Pages: 27

Brand: Asko Pages: 48

Brand: Teka Pages: 18

Brand: NEFF Pages: 32

Brand: Fagor Pages: 68

Brand: Cosmo Pages: 18

Brand: Maytag Pages: 28

Brand: Unox Pages: 36

Brand: Daewoo Pages: 43

Brand: Gram Pages: 28

Brand: Blodgett Pages: 94

Brand: IAG Pages: 26

Gorenje BCS547ORAW

Brand: ORA ITO Pages: 64

Brand: Gaggenau Pages: 60

Brand: Rangemaster Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands