background image

31

NOTE: Time change button is available only

with Manual Dry, Time Dry and Rack
Dry programs.

NOTE: Don’t use the rack for normal tumble

drying. The rack is shipped in place in your
dryer.  Please remove the rack before
using this dryer for the first time.

WARNING!

For better drying performance and safety,
clean lint filter every single use.

• Press MORE TIME or LESS

TIME until the desired drying
time is set.

3

Time Change Button

(1) Child Lock

Child Lock can be used to prevent children from
changing options on control panel while the dryer is
running. When Child Lock is enabled, all the buttons
will be locked and Child Lock will glow. To enable
Child Lock, Press and hold Beeper Dry for 3 seconds,
until there is a single beep tone and Child Lock is
displayed on the status window. To disable Child
Lock, press and hold Beeper Dry for 3 seconds again.

6

Child Lock

More Time

More Time

Less Time

Less Time

Rack Dry

Reduce Static

Anti-Crease

Mist

• When Anti Crease is selected,

the light for Anti Crease will
glow in the display.  When
power is on, CHECK FILTER
is displayed until start/pause is
selected.

4

Status/Clean Filter/Anti Crease Indicator

EST. TIME REMAINING

w

PROCESS

More Time

Less Time

Rack Dry

Reduce Static

R-WE5

Anti-Crease

• The display shows the

estimated time remaining. In
addition to this, if the dryer
has some problem, it displays
error messages. Refer to troubleshooting guide

5

Estimated Time Remaining

EST. TIME REMAINING

More Time

Less Time

Rack Dry

Reduce Static

Anti-Crease

Mist

More Time

Less Time

Rack Dry

Reduce Static

Anti-Crease

Mist

(1) CUSTOM PROGRAM

Set up your favorite
combination of settings and
save them here for one touch
recall.

1. Select a cycle.
2. Change DRY LEVEL and TEMP. CONTROL.
3. Select OPTIONS you want.
4. Press and hold the CUSTOM PROGRAM.

To recall your stored CUSTOM PROGRAM Press
CUSTOM PROGRAM button, then press
START/PAUSE.

(2) Rack Dry

Rack Dry is designed to use
for items which are not
suitable for tumble drying such
as sweaters, silk or lingerie.
This option may be used for drying Sneakers.

7

Option Buttons

More Time

Less Time

Rack Dry

Reduce Static

Anti-Crease

Mist

More Time

Less Time

Rack Dry

Rack Dry

Reduce Static

Anti-Crease

Mist

1. Open the door.

Hold the dryer rack with
both hands.

2. Put the dryer rack into the

drum. 

3. Make sure Dryer RACK is

evenly spaced right onto
the drum inside.

1

3

2

Summary of Contents for DWR-WE5413WC









































Reviews: